dogtired Posted September 3, 2016 Share Posted September 3, 2016 I am learning how to use my mini mill and there turns out to be a lot to know. Of course I am buying up a bunch of parts and guns to do some home gunsmithing projects (mostly because I am bored). My question is this: The host. I have a Tanfoglio EAA witness with the milled in front sight. I would like to replace it with something more useful. Of course a conventional dovetail is possible but I am looking at the traditional linear tanfoglio sight cut, or even a revolver type cut with a pinned in blank. In my Googling efforts, I can't find a dovetail cutter for the Tanfo front sight, or how to cut the pocket for a revolver front sight. Below is my junk slide used for practice. I milled off the sight and would like some guidance on technique. These slides are hard, I discovered the joy of carbide with this. Link to comment Share on other sites More sharing options...
Toolguy Posted September 3, 2016 Share Posted September 3, 2016 (edited) For the pin on type sight, you would use a carbide woodruff key cutter with the slide turned on it's side in the mill vise, then a carbide drill to do the pin hole. For the dovetail, you would use a 3/16" carbide end mill to hog out most of the meat and a carbide dovetail cutter from Brownell's or Harvey Tool to do the undercuts on either side. Edit to add: If you are doing the front to back dovetail, it is skinnier than the side to side ones. Do not use a 3/16 straight end mill for that one. Edited September 3, 2016 by Toolguy Link to comment Share on other sites More sharing options...
dogtired Posted September 3, 2016 Author Share Posted September 3, 2016 (edited) Thanks, thats a great start. Any idea of the Tanfo dovetail angle? Edited September 3, 2016 by dogtired Link to comment Share on other sites More sharing options...
Toolguy Posted September 3, 2016 Share Posted September 3, 2016 Most sight dovetails are 60 degree, some are 65 degree. I'm not sure which the Tanfo is, but whoever is selling them should know. Link to comment Share on other sites More sharing options...
MrPostman Posted September 3, 2016 Share Posted September 3, 2016 (edited) I will measure a Tanfo front sight when I get home. I had a link to the correct dovetail cutter in my old phone but I lost it when I upgraded. The dovetail cutter they use for the removable front sight is a special size, seems like it was a 3/16 by 70 degree. Edited September 3, 2016 by MrPostman Added content Link to comment Share on other sites More sharing options...
dogtired Posted September 3, 2016 Author Share Posted September 3, 2016 (edited) I measured a front at 70*, looks slightly larger than 3/16 at 0.2. Edited September 3, 2016 by dogtired Link to comment Share on other sites More sharing options...
GlennRasch Posted September 4, 2016 Share Posted September 4, 2016 (edited) I use a 9/64 and the CZ dovetail is 3/16 x 15deg. or 30deg (included) you'll have to move side to side a little and recut the sides. Edited September 5, 2016 by GlennRasch Link to comment Share on other sites More sharing options...
MrPostman Posted September 4, 2016 Share Posted September 4, 2016 (edited) 56 minutes ago, GlennRasch said: I use a 9/64 and the CZ dovetail is 3/16 x 15deg. or 30deg (included) Thanks for the info on the CZ. Edited September 4, 2016 by MrPostman Added content Link to comment Share on other sites More sharing options...
MrPostman Posted September 4, 2016 Share Posted September 4, 2016 (edited) 3 hours ago, dogtired said: I measured a front at 70*, looks slightly larger than 3/16 at 0.2. It is larger somewhat but it will work. They probably use a metric dovetail cutter for the factory cuts. Edited September 4, 2016 by MrPostman Correction Link to comment Share on other sites More sharing options...
BeerBaron Posted September 5, 2016 Share Posted September 5, 2016 yes it's quite likely the factory cutter is metric (everything else on the gun is). it's possibly 5mm which is a tiny bit over 3/16. you can of course widen the slot slightly if the cutter you get is undersize. Link to comment Share on other sites More sharing options...
kneelingatlas Posted September 5, 2016 Share Posted September 5, 2016 I would do a cross cut dovetail and use a 1911 front sight, much easier. Link to comment Share on other sites More sharing options...
dogtired Posted September 5, 2016 Author Share Posted September 5, 2016 But where is the adventure in that? Link to comment Share on other sites More sharing options...
kneelingatlas Posted September 5, 2016 Share Posted September 5, 2016 Link to comment Share on other sites More sharing options...
BeerBaron Posted September 5, 2016 Share Posted September 5, 2016 11 hours ago, kneelingatlas said: I would do a cross cut dovetail and use a 1911 front sight, much easier. yep, no need to worry about centering the cut then. and there's so many 1911 front sight options in type, width, height etc. easy to find the right dovetail cutter too. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now