terrydoc Posted October 14, 2015 Share Posted October 14, 2015 Thanks I had not seen those but can't get stuff sent from them to Australia anyway. Got the Boss hanger yesterday and fitted it looks good will try it over the weekend pity it doesn't fit my Safariland. Link to comment Share on other sites More sharing options...
Skywatcher Posted October 21, 2015 Share Posted October 21, 2015 so do these hangers fit all bladetech and safariland holsters Link to comment Share on other sites More sharing options...
The Donald Posted October 21, 2015 Share Posted October 21, 2015 so do these hangers fit all bladetech and safariland holsters They fit Bladetechs but need additional holes for Safariland. At one point Ben Stoeger Pro was going to make an adapter for the Safariland but very few people in USPSA use Safariland holsters. Link to comment Share on other sites More sharing options...
Nimitz Posted October 21, 2015 Share Posted October 21, 2015 (edited) I was the one who showed Ben how he could adapt his BOSS hoslter attachment for the Safariland ELS belt system (since I did it to mine).... if you have access to a drill press you can be operational in about 15 mins ... Edited October 21, 2015 by Nimitz Link to comment Share on other sites More sharing options...
terrydoc Posted October 21, 2015 Share Posted October 21, 2015 so do these hangers fit all bladetech and safariland holsters They fit Bladetechs but need additional holes for Safariland. At one point Ben Stoeger Pro was going to make an adapter for the Safariland but very few people in USPSA use Safariland holsters. Found them on his pro shop but none in stock at the moment Link to comment Share on other sites More sharing options...
MilkMyDuds Posted October 21, 2015 Share Posted October 21, 2015 You should be able to adjust lower. I can get mine low enough that it won't be SS legal and my production setup still has one more drop to go. Really does aid in drawing. I went through USPSA rule book and did not see any restrictions on how low the holster can do. It only has limit on "maximum lateral distance of the handgun and mag/speedloaders from the inner side of the belt", and "hip bone" position restriction. Where do you find how low the holster can go in the rule book? Link to comment Share on other sites More sharing options...
terrydoc Posted October 21, 2015 Share Posted October 21, 2015 (edited) 5.2.7.2 A holster with the heel of the butt of the handgun below the top of the belt, except as specified in Appendix D, or otherwise indicated in Rule 5.2.8. Missed this part in the appendix APPENDIX D5 — Single-Stack Division 20 Holster and magazine holder restrictions •Suitable for everyday use. “Race gun” type holster prohibited. •Must carry pistol so that the entire front strap (to the trigger guard) is at or above the top of the belt. Female shooters must carry the pistol no lower than the heel of the butt at the top of the belt. Edited October 22, 2015 by terrydoc Link to comment Share on other sites More sharing options...
MilkMyDuds Posted October 22, 2015 Share Posted October 22, 2015 5.2.7.2 A holster with the heel of the butt of the handgun below the top of the belt, except as specified in Appendix D, or otherwise indicated in Rule 5.2.8. Thanks! I tried it on the BOSS hanger (BladeTech holster). Even at the lowest setting, the heel of the butt of the gun still sticks above the belt by 1.5 - 2 inches. This may be gun specific but I do think a even lower setting would still be within the rules. Link to comment Share on other sites More sharing options...
aandabooks Posted October 22, 2015 Share Posted October 22, 2015 In SS the front strap of the gun has to be above the top of the belt. My son's holster is attached to one of my holster hangers in my avatar. He runs that setup for production. I could have a bracket on it that would allow for the gun to ride at mid-thigh but it wouldn't be legal or probably practical. Link to comment Share on other sites More sharing options...
TANFARM Posted October 31, 2015 Author Share Posted October 31, 2015 Received my boss hanger from Bens store last week ...simple to install and adjust.....locktite everything !!!!!! If you are using a 2011 model make sure you order the 3/4" spacers....simply will not work with the shorter ones. I was shipped the wrong spacers.....Ben's store sent me the correct ones N/C....that's all I can ask...very satisfied with everything I've purchased from Stoegers place......... Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now