Zuma Posted March 28, 2015 Share Posted March 28, 2015 Does anyone know the what size screws CZ uses for the Czechmate scope mount. I know I can order the stock screws from CZ USA, but I need to find longer screws so I can add a thumb rest. Thanks, Tom Link to comment Share on other sites More sharing options...
kneelingatlas Posted March 28, 2015 Share Posted March 28, 2015 M4x0.7 Link to comment Share on other sites More sharing options...
Zuma Posted March 28, 2015 Author Share Posted March 28, 2015 Thanks, kneelingatlas. I was hoping you would see this. If anyone would know it would be you. Tom Link to comment Share on other sites More sharing options...
kneelingatlas Posted March 28, 2015 Share Posted March 28, 2015 Link to comment Share on other sites More sharing options...
my00wrx1 Posted May 2, 2015 Share Posted May 2, 2015 What thumb rest have you mounted? Link to comment Share on other sites More sharing options...
kneelingatlas Posted May 2, 2015 Share Posted May 2, 2015 I've used a modified air soft thumb rest, but the harwar was junk and broke. I think the best choice at the moment is the Arredondo rest w/o mount holes. Link to comment Share on other sites More sharing options...
gng4life Posted May 2, 2015 Share Posted May 2, 2015 I found the longer screws on Amazon. I am working on a thumb rest now since I can't find one I like. The one Atlas recommended is good but I'm looking for something a little flatter. Sent from the range Link to comment Share on other sites More sharing options...
kneelingatlas Posted May 2, 2015 Share Posted May 2, 2015 I found the longer screws on Amazon. I am working on a thumb rest now since I can't find one I like. The one Atlas recommended is good but I'm looking for something a little flatter. Sent from the range Have you looked at the Allchin that screws to the bottom of the mount? Link to comment Share on other sites More sharing options...
gng4life Posted May 2, 2015 Share Posted May 2, 2015 Yeah, it looks way too small, I'm use to the Nitro Fin on my 2011s so just need larger area for my fat thumbs. I am looking at two options for a rest and will be trying them out in the next few weeks. Thanks for the recommendation. Sent from the range Link to comment Share on other sites More sharing options...
gng4life Posted May 2, 2015 Share Posted May 2, 2015 Does anyone know the what size screws CZ uses for the Czechmate scope mount. I know I can order the stock screws from CZ USA, but I need to find longer screws so I can add a thumb rest. Thanks, Tom Hey, if you just need a few screws, PM me your address and I'll drop them in the mail. Sent from the range Link to comment Share on other sites More sharing options...
Zuma Posted May 5, 2015 Author Share Posted May 5, 2015 gng4life, thanks for the offer. I was able to buy some screws. Tom Link to comment Share on other sites More sharing options...
gng4life Posted May 5, 2015 Share Posted May 5, 2015 No problem, let us know how it works out for you. Link to comment Share on other sites More sharing options...
lordres Posted May 6, 2015 Share Posted May 6, 2015 Which gas pedals are you looking at? I'm looking for one too! Link to comment Share on other sites More sharing options...
Zuma Posted May 7, 2015 Author Share Posted May 7, 2015 I am looking at the Arredondo without the holes. There doesn't seem to be many choices that use the Czechmate mount hole spacing. Link to comment Share on other sites More sharing options...
jdd817 Posted May 12, 2015 Share Posted May 12, 2015 For the thumb rest, I got the DAA with 3 holes, angled it a little bit and drilled and tapped an extra hole in the mount to keep the thumb rest from rotating. The only downside to this setup is you have to remove the thumbrest to disassemble the gun. My current plan is to remove a bit of material so that the slide pin can come out with thumbrest still attached. Link to comment Share on other sites More sharing options...
11287 Posted May 12, 2015 Share Posted May 12, 2015 For the thumb rest, I got the DAA with 3 holes, angled it a little bit and drilled and tapped an extra hole in the mount to keep the thumb rest from rotating. The only downside to this setup is you have to remove the thumbrest to disassemble the gun. My current plan is to remove a bit of material so that the slide pin can come out with thumbrest still attached. Could you post a picture of this set up both now and after you remove some material? Link to comment Share on other sites More sharing options...
jdd817 Posted May 12, 2015 Share Posted May 12, 2015 I can get the before once I get home.. have no clue when I'll get around to removing the material on the thumbrest itself. Link to comment Share on other sites More sharing options...
jdd817 Posted May 14, 2015 Share Posted May 14, 2015 Here's a picture of how I currently have the rest mounted. You can see the slide pin behind it, I plan to remove just enough to get the pin clear. Link to comment Share on other sites More sharing options...
banknotes Posted July 10, 2015 Share Posted July 10, 2015 (edited) I think you guys need to visit Advance Ratio Sports and Tactical in Facebook on your thumb rest issues....He made them even look better on CZ and TS, for right and left is available.... Edited July 10, 2015 by banknotes Link to comment Share on other sites More sharing options...
11287 Posted July 10, 2015 Share Posted July 10, 2015 I just ordered one. My shooting buddy just placed an order with Adrian for two black thumb rests I'll give a report back on it after I get it and install Link to comment Share on other sites More sharing options...
Hoosiershooter Posted July 10, 2015 Share Posted July 10, 2015 I'm waiting on a pedal from Adrian right now. I too will report in. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now