wscottstewart Posted December 15, 2014 Share Posted December 15, 2014 I picked up a 9mm witness limited barrel, put it in my 10mm limited frame & slide. It shoots accurately but I have cycling issues. It stovepipes every 4 rounds +/- I have tried several springs including the spring from my match 9mm without much change. I realize this could be the extractor, but seems unlikely to me compared to the spring. (Could be wrong) What spring rates should I try before giving up on fitting this barrel. Thanks in advance Link to comment Share on other sites More sharing options...
kneelingatlas Posted December 15, 2014 Share Posted December 15, 2014 You could go all the way down to 8# Link to comment Share on other sites More sharing options...
CleverUsername Posted December 15, 2014 Share Posted December 15, 2014 I ran into the same issue (10mm limited with 9mm barrel)and have tried lighter springs but I still had the same problem. I never got around to figuring it out Link to comment Share on other sites More sharing options...
Intercooler2 Posted December 15, 2014 Share Posted December 15, 2014 When I tried it the lightest spring worked best. 6lb? Still not optimal. Link to comment Share on other sites More sharing options...
jacob0 Posted December 15, 2014 Share Posted December 15, 2014 I wish I could have that problem. I just need to find a 9mm cone barrel. Link to comment Share on other sites More sharing options...
Nealio Posted December 15, 2014 Share Posted December 15, 2014 What is your 9mm load? If it's super light you can run a 6lb spring. Usually stove piping is due to short stroking. Does the slide move freely with the 9mm barrel in it? How many rounds on this gun? Link to comment Share on other sites More sharing options...
wscottstewart Posted December 16, 2014 Author Share Posted December 16, 2014 (edited) So far, I've just tested factory federal and win white box 9mm. 10mm base gun is fine with light factory loads & 9gr longshot with various 180 grain bullets. Gun is pretty new. Got used but was near new. I would guess around 1000 rounds or less. I've shot approx 200 - 250 10mm rounds Yes slide seems free by hand movement. Sent from my iPhone using Tapatalk Edited December 16, 2014 by wscottstewart Link to comment Share on other sites More sharing options...
Nealio Posted December 16, 2014 Share Posted December 16, 2014 It could be a little tight still, could be extractor tension, hard to say. Factory loads with a 10lb recoil spring should cycle fine. Are these all stock recoil springs? Link to comment Share on other sites More sharing options...
RIIID Posted December 16, 2014 Share Posted December 16, 2014 You are using a 10mm breech face with a smaller 9mm case, the case can slide out from under the extractor hook. The only thing you can do is get the extractor to apply more pressure to hold the case to the breech face until the case hits the ejector. Even then it may not be 100% reliable. Rich Link to comment Share on other sites More sharing options...
wscottstewart Posted December 16, 2014 Author Share Posted December 16, 2014 You are using a 10mm breech face with a smaller 9mm case, the case can slide out from under the extractor hook. The only thing you can do is get the extractor to apply more pressure to hold the case to the breech face until the case hits the ejector. Even then it may not be 100% reliable. Rich Yes I'm aware of that. However in many manufactures this is theoretical not fact. In some of them the two breech faces are exactly the same. So does any of you know this to be the case that these two guns are really different. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
Nealio Posted December 16, 2014 Share Posted December 16, 2014 Some people on here are running 9mm barrels in their .40's with (I thought) decent success. Ask kneelingatlas. So can you take a 9mm case, slide it up the breech face under the extractor, and see if it is holding in there with some force? If not you can file the "foot" of your extractor down just a tiny bit until it does. The foot is the square nub sticking out right behind the extractor blade: Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now