Birdkiller Posted June 24, 2013 Share Posted June 24, 2013 Hello, I've read the rule book on this section, and read a few threads, but haven't found my answer. I know stippling within the boundaries is legal, but is removing the factory texture prior to stippling to make the stipple more even legal? Specific I know, I just don't want to screw up my production gun. Thanks, Cole Link to comment Share on other sites More sharing options...
dskinsler83 Posted June 24, 2013 Share Posted June 24, 2013 In my opinion as a new RO that would be illegal as it would reduce the grip in areas and grip reduction is illegal in production Link to comment Share on other sites More sharing options...
atbarr Posted June 24, 2013 Share Posted June 24, 2013 I don't think you can modify ANYTHING that is visible. But, I've been wrong before. Link to comment Share on other sites More sharing options...
dskinsler83 Posted June 24, 2013 Share Posted June 24, 2013 You can stipple in the areas provided in the shaded in the RULE BOOK Link to comment Share on other sites More sharing options...
Jay870 Posted June 25, 2013 Share Posted June 25, 2013 There is ruling that says grinding down factory texture to apply epoxy & grit is legal, so I would say grinding down factory texture to apply stippling is also legal. Link to comment Share on other sites More sharing options...
GrumpyOne Posted June 25, 2013 Share Posted June 25, 2013 There is ruling that says grinding down factory texture to apply epoxy & grit is legal, so I would say grinding down factory texture to apply stippling is also legal.Not true: here is the ruling:Question:I was wondering if an epoxy treatment filling in the voids of the grip of an XDm would violate section 22.2 of Appendix D4. Answer:21.4 states: For semi-automatic Production guns, grip tape, grip sleeves, checkering, stippling or other texture may only be applied in the areas shown in appendix E4. Glue and grit is considered the same as stippling. The procedure offered by the vendor you referred to is nothing more than epoxy (glue) with a grit (same as stippling and therefore legal as it does not change the profile of the grip. Nowhere does it say grinding down the grip is legal. Only that filling in the voids is legal, and applying grit in the areas described in E4. Link to comment Share on other sites More sharing options...
dskinsler83 Posted June 25, 2013 Share Posted June 25, 2013 There is ruling that says grinding down factory texture to apply epoxy & grit is legal, so I would say grinding down factory texture to apply stippling is also legal.Not true: here is the ruling:Question:I was wondering if an epoxy treatment filling in the voids of the grip of an XDm would violate section 22.2 of Appendix D4. Answer:21.4 states: For semi-automatic Production guns, grip tape, grip sleeves, checkering, stippling or other texture may only be applied in the areas shown in appendix E4. Glue and grit is considered the same as stippling. The procedure offered by the vendor you referred to is nothing more than epoxy (glue) with a grit (same as stippling and therefore legal as it does not change the profile of the grip. Nowhere does it say grinding down the grip is legal. Only that filling in the voids is legal, and applying grit in the areas described in E4. That's my opinion on the ruling as well. There is no removing any material from the grip that I'm aware of Link to comment Share on other sites More sharing options...
Jay870 Posted June 25, 2013 Share Posted June 25, 2013 There is ruling that says grinding down factory texture to apply epoxy & grit is legal, so I would say grinding down factory texture to apply stippling is also legal.Not true: here is the ruling:Question:I was wondering if an epoxy treatment filling in the voids of the grip of an XDm would violate section 22.2 of Appendix D4. Answer:21.4 states: For semi-automatic Production guns, grip tape, grip sleeves, checkering, stippling or other texture may only be applied in the areas shown in appendix E4. Glue and grit is considered the same as stippling. The procedure offered by the vendor you referred to is nothing more than epoxy (glue) with a grit (same as stippling and therefore legal as it does not change the profile of the grip. Nowhere does it say grinding down the grip is legal. Only that filling in the voids is legal, and applying grit in the areas described in E4. You're right! Thanks for the catch & correction! Link to comment Share on other sites More sharing options...
Birdkiller Posted June 27, 2013 Author Share Posted June 27, 2013 So, knocking off the corners of the grenade checkering prior to stippling is going to knock me out of production. Is that what I'm hearing? Thanks for the replies, BK Link to comment Share on other sites More sharing options...
dskinsler83 Posted June 27, 2013 Share Posted June 27, 2013 I would say yes Link to comment Share on other sites More sharing options...
GrumpyOne Posted June 27, 2013 Share Posted June 27, 2013 So, knocking off the corners of the grenade checkering prior to stippling is going to knock me out of production. Is that what I'm hearing? Thanks for the replies, BK Are you removing material from the grip? If so, then yes, it would knock you out of production. Link to comment Share on other sites More sharing options...
EkuJustice Posted June 29, 2013 Share Posted June 29, 2013 In all honesty once its stippled it is hard to tell what if anything was removed from the grip unless its extreme ie removing finger groves etc Link to comment Share on other sites More sharing options...
GrumpyOne Posted June 29, 2013 Share Posted June 29, 2013 In all honesty once its stippled it is hard to tell what if anything was removed from the grip unless its extreme ie removing finger groves etc In all honesty, we're counting on the integrity of all shooters to do the right thing. How many threads have there been about shooters cheating? Doesn't matter how much you cheat, it's still cheating. And once you start down that slippery slope "Well, its just a bit of grinding....Since the didn't notice the grinding, maybe I can remove some metal from the inside of the slide...etc", its damn hard to keep from sliding further. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now