Nemesis Lead

trgt--I have the 10 round version of the mag on the right and I like the basepad in the middle. Is there an ap for that?

Hi Guys, I own 10 round mec gar magazines and run them in an CZC AccuShadow. They have identical tubes to the 17 round mec gar magazines but with dimples to prevent you from loading more than 10 rounds (yes I live in CA). My question is......what basepads do folks like with these magazines? Looking for something that will: 1) help brace the support hand (by the pinkie finger). I like my friend's 19 round magazines because you get a little more contact area to control recoil. 2) Is easy on/easy off so I can clean mags as I drop them. 3) Doesn't add capacity (since I live in a Totalitarian state). Thoughts?

Thanks guys. Do the sights come out easily? I am a bit concerned about hammering the thing out and ruining the Dovetail or old front sight.

Hi Guys, I am having some front / rear sight issues with my new AccuShadow and was wondering.......does the CZC AccuShadow simply use standard Shadow front sights without a roll pin? Installation is just to drift the front sight in from front to back? The sight is held in by the bushing and a tight fit on the dovetail? I also understand that AccuShadows CANNOT use a roll pin in the front sight. Please correct me on any of the above. I am new to CZs and could easily be dead wrong here. If there is anything else I should know about installing a front sight on an AccuShadow, please let me know. I have a friend with an AccuShadow who has a loose / wobbly front sight because of an improper install and I don't want to follow in his footsteps! Many thanks! Jay

Uh-oh. Now I am confused. I did buy the half mount, so it should come with a casefeeder then?

Does the Dillon casefeeder come with the Case Pro?

Just wondering what kind of experiences folks have had with a casepro 100. I just placed an order for one and wanted to see what folks thought.

Hey Sarge, My stuff is lubed and it will case gauge. It is just tighter than my Dillon which really surprised me!

Guys, In 9mm what is the best sizing/decapping die for removing bulges in the bottom of my case? I went from Dillion to the EGW undersize die (.01 undersize) thinking that would be an improvement. The EGW was actually not as good as the Dillon. Who makes the best die for this?

No--don't have a JP 15 lower. Was thinking about getting one.

Actually I just choked up on the failsafe rod and that seemed to solve the issue.

Hi Guys, A problem I have never seen before. We all want the "slide" in our powder die to make a full throw so we know we get a full and consistent powder charge. I have one that goes TOO FAR. It moves all the way forward and actually binds up my machine. How do you decrease the travel of that "slide" (sorry not sure what the technical name for it is)? I had thought about raising the entire die on the toolhead, but that would reduce how much my cases were belled. Anyone have a good thought here?

Thanks Jay. How about a JP 15 lower? Are those "milspec?"

This may be an ignorant question but I have to be certain! I have a JP CTR-02 that I love dearly. I got a good deal on a BCM upper and was thinking of getting it and running it on the JP CTR-02 lower. Are there any technical issues here? It would be the complete CTR-02 lower mated with a complete BCM upper including a BCM bolt carrier. Basically, the JP upper would be my "game rifle" and the BCM upper would be a "defense rifle." Just trying to save a little dough and run one lower for both purposes (and yes, my lower does have a heavier trigger).

Thank you! Surprised at your OAL considering all that I have read!

I have a new CZ (9mm AccuShadow) on order. CZ custom tells me that CZs like short bullets. They recommended the following: A 124 grain Zero JHP loaded to 1.09 with Federal Primers. They also liked N320 as a powder, but did not recommend a charge weight (perhaps understandable). My question is......how many grains of N320 powder should I use to get to 130 PF? Please don't speculate. I am sure that someone is running this exact load in a CZ 75 SP01 since CZ Custom recommended it!

I am new to the CZ platform and want to know how to completely disassemble and reassemble my CZ 75 SPO1. Is there a DVD or internet video that is better than the rest for this purpose? Many thanks!

I did. Motor burned out. They are sending a new motor.

I run a Dillion Super 1050 hooked up to a Forcht auto-drive system. I run this exclusively for 9mm. I run Dillion dies and have been getting 2 rounds per hundred not case gauging. I was thinking of putting a Lee U-Die size-decap die into my machine to see if I could reduce my "reject rate." Has anyone run the Lee U-die die in an automated 1050? The reason I ask is that I hear the U-Die will chip brass, but I heard that ONCE so it might just be internet noise. If not Lee, is there a better die that can help here? Many thanks!

Some great thoughts here. I have done dry fire and live fire and it has not gone well. I will add a couple of the exercises mentioned above and see what happens!

So I have always shot with tape over my left eye. I took a Manny Bragg class this weekend and he encouraged me to take the tape off. I have decided to give it a shot. 2 days of dry fire with both eyes open and unobstructed. The results so far--terrible. I see either 2 front sights or 2 targets. Tomorrow will be my first day of live fire with this. 2 questions: 1) For those who have been down this road......is there a light at the end of the tunnel? 2) Are there any specific drills that can speed this process up. Tomorrow is the first day of live fire.

Thank you for the response. I have a 4 MOA T1. Looks like they make a 2 MOA version now as you point out. Which scope offers you better overall "vision" for transitions, etc.. The T1 has more vision "around" the scope because it is smaller, but do you ever have issues with the smaller tube vs the M4?

Hey Head--Which version of the SLR Sentry did you get? If it worked for you, it will likely work for me.

I have an Aimpoint M4 which I use in Limited. I am interested in looking at an Aimpoint T1 as old football injuries have me looking to lighten my rifle. Has anyone ever moved from an Aimpoint M4 to an Aimpoint T1? Seems much lighter albeit with a bigger dot. My question is.......how did you like the T1 vs the M4? In what ways was it better? In what ways was it worse? Are the equivalent on up close targets? Did it have an impact on your scores/placing in a match? Which is better overall for Multigun?

The title says it all. Will my JP Low Profile Gasblock fit underneath a BCM KMR 15 handguard? My understanding is that there must be a little play as the barrel will move under recoil and/or the handguard could get pushed into the gas block if you are leaning into a position. I would appreciate responses from folks who have done this installation. Many thanks!