triplesinglestack
-
Posts
287 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by triplesinglestack
-
-
I did try the club finder on the uspsa wesite, but it only searches so far, came up blank on the zip code search
Yes, I work with homeland security.
I was hoping there would be something a little closer than 2 hr drive, I guess Living in SO, Cal for ever spoiled me.
-
just like the topic.....
I'm moving to Lordsburg New Mexico, in a few months, are there any clubs near there? I know its about 2 hours east of Tucson AZ, ???
-
sorry meant to post in the rules sub cat.....
-
So at the local club match the other day, a guy had a CZ (75?) 9mm but it was SAO, (single action only), but to be fair to the rules of production, he lowers the hammer prior to the start, then manual cocks the hammer after the start signal, and runs COF, is this legal? if so why/why not? thanks.
-
So does anyone know if they are ever gonna start making these things again? I want one but they are almost impossible to find, and the ones I do come across, well, the owners are quite proud of them......
-
I am not going to discuss laws and such here, since we have a forum already in place to discuss CA laws etc.
www.calguns.net
but my advice is to shoot SS division since you are already geared up for it, and once you start shooting, you will be able to understand more about the "standard capacity mag laws"
welcome =)
-
was best race I've seen in quite a while, I won't spoil it for those of you w/DVR, but real good race
-
-
-
here are mine, millenium edition on the left, also a backup for my production gun on the right.
-
the one on the left is a "Millenium" I believe, limited run from 2000 w/special SN starts w Y2K, and some nice factory grips, the other on is a plain jane 92fs, w/some trigger work and production legal mods
-
does anyone know if the bladetech holster designed for the Springfield TRP (full rail) will also accomodate the following pistols:
Kimber Warrior (rail)
Springfield MC Operator (full rail)
the website seeems a bit vague, and my search seemed more torwards holsters w/lights, I have no intention of attaching a light/lazer etc. to these weapons, as I only shoot USPSA w/these guns.
thanks
J
-
I have a springfield loaded 9mm, that has a few miles on it, the breech face is showing some pitting (not too bad) slide to frame is getting sloppy, and the barrel may be okay, but I'm thinking I heard somewhere that you could open the breech face and change barrels on this model and have a .40 S&W, I searched several topics and did not find anything, thanks
J
-
-
I have the Jager kit on a G22, if you want some starting load data PM me for details, it is fun, and I do not feel at a disadvantage to the 9mm or 38 sc 2011.
but I am just a C class shooter
-
I have the classic cast turret press, and it is great for low volume high quality stuff, keep it mounted right next to my Dillon, is great for working up loads, and a back up for if the dillon goes down......(hasn't happened yet).
-
so after reading through all 4 pages in the Beretta section, I did not find a firm answer to my questions. I shoot USPSA and would like to have an extended mag release, skeleton hammer and a mainspring housing minus the lanyard loop, but want to avoid shooting Open minor with my Beretta 92fs and 10 rd mags.Any suggestions? I have been to the olhasso website, but want to make sure all parts are legal prior to ordering. Thanks again
J
-
can't really help you, but I have been shooting a model 28 for over 20 years, you cant wear it out, I love mine. may want to try the hks speedloaders I think part # 27A? I like them fine. I have some old safariland speedloaders, If you send me a picture of what you are looking for I will check and if they are the same you can have them.
Jason
-
can't really help you, but I have been shooting a model 28 for over 20 years, you cant wear it out, I love mine. may want to try the hks speedloaders I think part # 27A? I like them fine. I have some old safariland speedloaders, If you send me a picture of what you are looking for I will check and if they are the same you can have them.
Jason
-
installed a dawson firing pin, extended and went to the range, 250 rds, federal primers, ran 100 % additional 50 rounds factory ammo ran 100 % firocchi?
-
also have a S&A arched magwell installed
-
gun is new to me w/unknown history, problem existed prior to me owning gun,
my load is: 147 gn bear creek moly, over 3.1 gns clays, fed 100 primers oal 1.140-1.145.
19 lb hammer spring
11 lb recoil spring
brazos trigger kit (light weight hammer titanium strut,)
titanium STI main spring cap
titanium firing pin (w fresh spring)(also cleaned channel)
firing pin stop appears new and measures .132" thick (front to rear)
firing pin while assembled protrudes through back of FPS .027"
firing pin OAL is 2.288"
Hammer is making full contact against FPS and is flush.
-
yeah, I would like to fix it........I am being told that the stock Titanium Firing pin is the culprit, and if I have to replace it anyways, why not get an extended one? any cons?
Jason
-
I understand that I can convert the safetys on my beretta 92fs so that they are decocker only, and spring loaded so not a safety? how do I do this and where do I get the parts?
thanks
BTW I searched all 3 pages in the beretta sub topic
USPSA near Lordsburg New Mexico?
in Travel, Locations, Ranges, etc.
Posted
thanks for all the help, have some good leads to check out