practical_man Posted September 28, 2008 Share Posted September 28, 2008 (edited) Problem: Last round of every magazine fails to eject. Empty brass is usually 90degrees to bore axis, case head facing away from the ejection port. This only happens when there is no round remaining in the magazine. If there is a round in the magazine, the pistol consistently ejects over my right shoulder. I've tested this with 1, 5, 10, and 16 rounds in the magazine. Same result, last round fails to fully eject. Details. - Happens with Winchester White Box and UMC factory ammunition as well as reloads (125grain over 4.2 grains of 231 and WSP primer) - Pistol is a 1st GEN Glock 17. Box says it's a factory rebuild. Pistol is bone stock, except for a Lone Wolf 3.5 pound connector. - Failure to eject occurs with the two 17 round magazines that came with the pistol, as well as 3 factory Glock magazines I bought from Brownell's last month. - Happens whether pistol is dirty or just cleaned. - I have completely disassembled the slide for cleaning. That didn't help. I put one small drop of oil inside the extractor channel. A little slide-glide on the rails. - The ejector looks fine. No chips, no cracks. Angled to the right so it hits the round a little left of center. ETA: This doesn't happen with my G19 or G21. I don't think it's operator limp-wristing at the end of the string of fire. This is driving me a little nuts. Any ideas? -john Edited September 28, 2008 by practical_man Link to comment Share on other sites More sharing options...
dirty whiteboy Posted September 29, 2008 Share Posted September 29, 2008 How many rds on the ejector? Look to see if it is bent down at the tip. I never put oil in the extractor channel. I wonder if the mag release is worn on the inside and the mag is sitting lower than normal, just a thought. Link to comment Share on other sites More sharing options...
practical_man Posted October 4, 2008 Author Share Posted October 4, 2008 I have no idea how many rounds on the ejector. It isn't bent down. I'll try holding the mag up to see if that's a contributing factor. thanks, john Link to comment Share on other sites More sharing options...
jobob Posted October 4, 2008 Share Posted October 4, 2008 Sounds like an extractor problem. It's ok when there is another round pushing it up which pops it out of the port. When that round isn't there, your empty just falls off of the extractor before it can hit the ejector. Look very closely at the extractor. The bottom edge may have a chip out of it. That can happen with lots of use, or when someone drops the slide on a loaded chamber. Replacing the extractor is easy, and will more than likely fix your problem. Link to comment Share on other sites More sharing options...
redmanfixit Posted October 4, 2008 Share Posted October 4, 2008 I would consider replacing the extractor spring as well. Springs do get weak with time and sometimes there are variations in manufacturing....even for Glock. +1 0n replacing the hook. Link to comment Share on other sites More sharing options...
Duane Thomas Posted October 4, 2008 Share Posted October 4, 2008 Does your gun have the new style LCI extractor, or the older "flat" extractor type? Link to comment Share on other sites More sharing options...
practical_man Posted October 5, 2008 Author Share Posted October 5, 2008 Does your gun have the new style LCI extractor, or the older "flat" extractor type? Old-style flat extractor. I'll get a new extractor and ejector. They're cheap enough Thanks, John Link to comment Share on other sites More sharing options...
Duane Thomas Posted October 5, 2008 Share Posted October 5, 2008 When you do, let us know what happens, please. Link to comment Share on other sites More sharing options...
gotm4 Posted October 5, 2008 Share Posted October 5, 2008 Does your gun have the new style LCI extractor, or the older "flat" extractor type? Old-style flat extractor. I'll get a new extractor and ejector. They're cheap enough Thanks, John Be sure that you get the correct 'spring loaded bearing' for the extractor you'll be using. There's two different ones used between non-LCI and LCI. Also be sure to clean out the slide in the extractor area. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now