chp5 Posted December 7, 2004 Share Posted December 7, 2004 Don't know if this thread belongs in the Gunsmithing section or here, but here it goes. I'd like to shorten my pump shotgun buttstock (wooden) about 1". Any tips on the best way to do this and then how to fit the buttpad to the shortened stock? Actually, the buttstock without the buttpad is about the right length for me, but I don't have anyting to cover the bare end of the woodend stock. Thanks for any ideas. Link to comment Share on other sites More sharing options...
diehli Posted December 7, 2004 Share Posted December 7, 2004 Are we talking an 870 w/o anything in the buttstock (I have limited experience with other shotguns). If so, I'd think that a saw and beltsander would be the best things, then a drill for pilot holes for the screws. As far as the pad, get one of the Simms that can be sanded down from Brownell's, wrap a couple of layers of duct tape around the wood and use a Dremel or that belt sander at a VERY slow speed to take the excess off of the sides of the pad. Link to comment Share on other sites More sharing options...
Patrick Sweeney Posted December 7, 2004 Share Posted December 7, 2004 Shortening a stock and putting a pad on it is one of those home gunsmithing jobs that look easy, and you only ever do one of them once you find out what it entails. First, shortening the stock. If you get the angle wrong, you can change the pitch, and end up with a stock that either slides off your shoulder, or jumps up and smacks you in the face on each shot. You can almost never re-use the old pad. The screws invariably end up in the wrong places on the new back of the buttstock. You need the next size smaller from Brownells. You want a big belt sander, a new belt, and a high speed. Too slow, or dull, and it grabs the rubber rather than cut it. If you're luccky it will only be "grabby" enough to tear the edges of the pad. If you're unlucky it will snatch the stock out of your hands. You also use the belt sander to sand the newly-sawn buttstock, before you apply some kind of sealer to keep the wood from warping when it gets wet. Use masking tape, not duct tape. Two layers, and use a colored marker on the top layer. When the belt sander starts cutting color off, exposing fresh tape, you're close. Wear a mask. All this sanding will fill the air (and your lungs, if you don't wear a mask) with wood and rubber dust. I fitted pads on stocks for almost twenty years, (after the shoeshop that did the fitting before for me, went out of business) and hated it. I got to the point where I'd do them only after I had enough to warrant the hassle, and then do them all in an afternoon. Then tried (in vain) to clean up the dust all over everything. Obviously, do the work after lunch. I hope I convinced you to take it to a professional. Link to comment Share on other sites More sharing options...
diehli Posted December 7, 2004 Share Posted December 7, 2004 Hey... mine wasn't too bad for a guess. Link to comment Share on other sites More sharing options...
chp5 Posted December 7, 2004 Author Share Posted December 7, 2004 Thanks Patrick. The stock without the buttpad is about the right length. I wonder if I can just get a flat buttplate (no pad) and put it over the end of the buttstock. It would still be the correct length, but no pad. It is a Winchester 1300. Link to comment Share on other sites More sharing options...
rhino Posted December 8, 2004 Share Posted December 8, 2004 It might be easier in the long run to get a reduced length stock and just swap 'em. Link to comment Share on other sites More sharing options...
chp5 Posted December 8, 2004 Author Share Posted December 8, 2004 It might be easier in the long run to get a reduced length stock and just swap 'em. True, true . . . Thanks for the replies. Link to comment Share on other sites More sharing options...
rhino Posted December 8, 2004 Share Posted December 8, 2004 It's what I did/do! I am very happy with the youth model SpeedFeed stock on my Rem 1100. I'm in the process of finding the shortest stock on the market for my dad's 870. Link to comment Share on other sites More sharing options...
scotty Posted December 8, 2004 Share Posted December 8, 2004 All of Patrick's cautions apply, but... Shortening a stock and fitting a buttpad is not rocket science. You just need to be careful and have plenty of patience. I did my first job using a radial arm saw to cut the stock and a portable belt sander clamped into my bench vise to fit the pad. Came out nice. I have since acquired better tools that make the job easier, but they don't come out any better. The most critical part is cutting the stock parallel to the existing face. I don't know what the going rate is for have having it done professionally, but for me it means the difference between havin a new buttpad or not having one. Link to comment Share on other sites More sharing options...
stingerjg Posted December 8, 2004 Share Posted December 8, 2004 Thanks Patrick. The stock without the buttpad is about the right length. I wonder if I can just get a flat buttplate (no pad) and put it over the end of the buttstock. It would still be the correct length, but no pad. It is a Winchester 1300. have you ever shot a 12ga pump with no pad on it? its not very fun unless your wearing several layers of clothing. Can you say, ouch?! Link to comment Share on other sites More sharing options...
bpowe Posted December 8, 2004 Share Posted December 8, 2004 Also, be sure to wrap the stock with masking tape or scotch tape before cutting. This will greatly reduce splintering if your saw blade is not extremely sharp or is too coarse. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now