Ty Hamby Posted May 20, 2013 Share Posted May 20, 2013 (edited) I had a crunch in the trigger pull. Slight but noticeable. I took the side plate off and couldn't figure it out. I took the hammer off and discovered it was still there. Upon closer examination I see it is riding the frame and that is the point the trigger pull gets choppy. This is an original 627-PC. There are less than 100 rounds through it. The trigger and hammer are slightly sloppier on the studs than my newer 627's with thousands and thousands of rounds on them. I am thinking the clearances from the original Lew Horton ones may have been more than the modern machines do today. What say you revolver junkies? Shim or clearance the trigger? Edited May 20, 2013 by Ty Hamby Link to comment Share on other sites More sharing options...
Waltermitty Posted May 20, 2013 Share Posted May 20, 2013 I shim all of mine. Only way to be sure. Link to comment Share on other sites More sharing options...
gp100man Posted May 20, 2013 Share Posted May 20, 2013 2nd on the shim. Btw, what is all of that "stuff" in there? Steve Link to comment Share on other sites More sharing options...
Ty Hamby Posted May 20, 2013 Author Share Posted May 20, 2013 The goo is grease. Apex greased up the action when they fitted the Ti cylinder a while ago. I'll get some shims coming. Myself being left handed torques the trigger a little differently than others. I though new gun maybe it would slick up. Many dryfires later its only getting more pronounced so I slid the side plate off and discovered it was striking the frame. I have lots of time for me to dial this one into how I like it. This is my 2014 and beyond ICORE gun and not my backup or IRC primary. I'm giving up on 38 super. Thanks guys. Link to comment Share on other sites More sharing options...
PatJones Posted May 20, 2013 Share Posted May 20, 2013 The trigger stud may be crooked, it doesn't take much to make things rub. Link to comment Share on other sites More sharing options...
Shadowrider Posted May 27, 2013 Share Posted May 27, 2013 The trigger and hammer are slightly sloppier on the studs than my newer 627's with thousands and thousands of rounds on them. I am thinking the clearances from the original Lew Horton ones may have been more than the modern machines do today. What say you revolver junkies? Shim or clearance the trigger? This is one of my biggest peeves. Shim that puppy. Link to comment Share on other sites More sharing options...
Tom E Posted May 28, 2013 Share Posted May 28, 2013 Looks like the stud may not be square to the frame. Soo, shim it. I almost always have 1 or 2 shims installed. If it still contacts trim the trigger a little. It's an area of no consequence in a DA only gun. You can bend the stud a little which is probably the "correct" fix but that has a higher chance for disaster. Link to comment Share on other sites More sharing options...
bountyhunter Posted May 28, 2013 Share Posted May 28, 2013 (edited) Welcome to the world of the PC. I bought a PC 627 about five years back...... and spent a big chunk of my life fixing all the problems. If all you need is a shim or two..... go for it. Good luck. Edited May 28, 2013 by bountyhunter Link to comment Share on other sites More sharing options...
pskys2 Posted May 28, 2013 Share Posted May 28, 2013 Gently see if the Stud will wiggle any. I've had several break. It is easy to bend them, but they should not have any wiggle in them. If it's ok, shim it, I like to do both sides even. Just make sure the hammer still moves freely with the side plate on. Link to comment Share on other sites More sharing options...
bountyhunter Posted May 29, 2013 Share Posted May 29, 2013 (edited) Gently see if the Stud will wiggle any. I've had several break. It is easy to bend them, but they should not have any wiggle in them. If it's ok, shim it, I like to do both sides even. Just make sure the hammer still moves freely with the side plate on. Also check for hammer drag on side plate or frame. Couldn't count how many SWs I have had to fix with that problem. Most seem to lean to the right. Edited May 29, 2013 by bountyhunter Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now