Chills1994 Posted September 8, 2011 Share Posted September 8, 2011 Hi all, I am just wondering if there are any tips for making it easier and faster to cut external (male) threads on some 1/2 inch diameter rod??? I spun the ends of the rods against a 12 inch disc sander to put a slight taper on them. I also use tapping oil. The smallish handles of the die wrench are getting my hands sore. I will go like a quarter turn... Hear it cutting ... Then back it off to break the chips. I will get so far and then unscrew the die box completely, tap it against the workbench to get all the chips out. Then start again. Any advice? Link to comment Share on other sites More sharing options...
shred Posted September 8, 2011 Share Posted September 8, 2011 If you have some way to thin the OD of the rod so it corresponds to the actual thread height of your thread (since threads are not perfectly pointy, the spec is not 0.5"), that will help. It will probably be tough to do that without a lathe though. 1/2-13 threads are 0.483" diameter 1/2-20, 0.489" Link to comment Share on other sites More sharing options...
bull2700 Posted September 8, 2011 Share Posted September 8, 2011 Per Machinery's handbook 1/2-13 UNC class 2A threads; major dia. min. .4876, major dia. max. .4985 Link to comment Share on other sites More sharing options...
tracker Posted September 8, 2011 Share Posted September 8, 2011 (edited) Per Machinery's handbook 1/2-13 UNC class 2A threads; major dia. min. .4876, major dia. max. .4985 If your Die is adjustable, turn the adjusting screw in a bit......not too much or you could brake the die or it may not fit back into your die stock. Back it off for the first pass, then re adjust back to origional setting and take another pass. you can check fit with a nut. Maybe even try 3 passes. As a tip........for any threading a cheap alternative (and safe) to cutting oil is canola oil. If you have a choice in material selection choose 12L14 or 12L15. Free machining steels. Will cut easier and produce better surface finish. Edited September 8, 2011 by tracker Link to comment Share on other sites More sharing options...
shred Posted September 9, 2011 Share Posted September 9, 2011 Per Machinery's handbook 1/2-13 UNC class 2A threads; major dia. min. .4876, major dia. max. .4985 I was figuring a 1A would probably be ok, seeing as how he's doing it by hand with a die The other alternative is to just go get some all-thread and weld a bit of that on the end. Link to comment Share on other sites More sharing options...
ihatepickles Posted September 9, 2011 Share Posted September 9, 2011 Find a plumbing truck parked at McD's around lunchtime? Link to comment Share on other sites More sharing options...
Chills1994 Posted September 10, 2011 Author Share Posted September 10, 2011 Thanks for the replies everyone. I didn't know that about the actual thread dimensions. The rods I am using now measure around .501 or .502. I am so glad I whittled a taper to the ends with the disc sander first. That made things so much easier getting the die started. It was taking me about 7 minutes per each end of the rod to thread. I ended up putting a cheater pipe to my vise's handle so the rods wouldn't spin. With vises that are meant to swivel...well...I have to question where they put the clamping bolt and handle that actually locks everything down to the base. I am half tempted to cut off the handle, unscrew the bolt, and then weld both halves back together, permanently. I will have to price out half inch smooth rod versus half inch all thread.... maybe for the Mark II version I might just go with all thread instead of sinking all that time into cutting threads on the end. Link to comment Share on other sites More sharing options...
kevinj308 Posted September 11, 2011 Share Posted September 11, 2011 Adjustable die, makes life a lot easier. Non adjustable dies are really meant for chasing existing threads. They'll cut new ones, but they don't like it. Hope it works out for ya Kevin Link to comment Share on other sites More sharing options...
Sudden Death Posted September 12, 2011 Share Posted September 12, 2011 The easiest way is to buy all-thread Link to comment Share on other sites More sharing options...
jmorris Posted September 13, 2011 Share Posted September 13, 2011 Adjustable die, makes life a lot easier. Non adjustable dies are really meant for chasing existing threads. They'll cut new ones, but they don't like it. +1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now