Taipan Posted August 23, 2010 Share Posted August 23, 2010 Hi could someone tell me what part of this they have removed I have taken the notched part off my 1050 and made up the distance of the metal with a washer of the same thickness but when I stroke the press it moves at least 6-10 mm sideways on the downward stroke and that to me seems way to much. The last thing I want to do is to have the toolhead hit the shellplate is this kind of movement normal after you have taken off this part or should I just take off the spring loaded pawl that runs up and down the that notched bar. To me that pawl is not going to last long at any rate as the sawing action of this setup is already starting to wear it away . I have put the notched bar back for now just to be on the safe side and wait until I get some advice from the 1050 Guru's on this site. & Thanks in advance to any replies Link to comment Share on other sites More sharing options...
larry cazes Posted August 26, 2010 Share Posted August 26, 2010 A large percentage of users here disable the ratchet right away when they get a 1050. Mine started malfing after a few hundred rounds. Do a search for this and you will see a lot of posts outlining how best to do it. Link to comment Share on other sites More sharing options...
Bigpops Posted August 26, 2010 Share Posted August 26, 2010 Ditto. Have one hang-up to where you need to raise the toolhead and clear some rounds...you will curse that thing! I took it off ASAP. It sounds like you have it right. I will need to look at mine but I believe I still have the notched bar attached. Link to comment Share on other sites More sharing options...
Aircooled6racer Posted August 26, 2010 Share Posted August 26, 2010 Hello: I removed the lever arm that is attached to the press not the ratchet that is attached to the toolhead. Take note that when removing the lever arm that the ball and spring behind it may fall out. The press is alot smoother with the rachet system removed but take note that it is also easier to get a over charge without it. When in daught take the brass out :cheers:Thanks, Eric Link to comment Share on other sites More sharing options...
markcic Posted August 26, 2010 Share Posted August 26, 2010 1050 Manual The easy way to disable it without taking anything off is to push ratchet back (13376 - Ratchet Restriction Tab) and tighten the screw on the left (20635 - Ratchet Detent Assembly). Link to comment Share on other sites More sharing options...
Bigpops Posted August 26, 2010 Share Posted August 26, 2010 1050 Manual The easy way to disable it without taking anything off is to push ratchet back (13376 - Ratchet Restriction Tab) and tighten the screw on the left (20635 - Ratchet Detent Assembly). I just looked that up...looks good! Thank you! Link to comment Share on other sites More sharing options...
Taipan Posted August 27, 2010 Author Share Posted August 27, 2010 (edited) Ok it seems that removing it is the way to go, the funny thing is the manual I got with my press does not even show that Ratchet & Pawl I must have been given the older version of the 1050 manual with my now four week old press. Could someone tell me just how much movement they have in the toohead when they cycle the press as stated above I get about 6-10 mm movement without the rachet on the press is this what is considered normal movement. Thanks to any reply Edited August 27, 2010 by Taipan Link to comment Share on other sites More sharing options...
larry cazes Posted August 31, 2010 Share Posted August 31, 2010 Dillon has had a fix for the issues with this part of the press for at least 2 years now. Heard about it at the booth at Area2 last year. Funny, I just took mine off after arguing about it with Dillon service the first week I had the press. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now