wbkr68

The canik is a great gun. Got two of them and shoot carry optics.

I've been using sns for a couple years. Like them alot!

You'll love this gun! Got around 3000rds on mine. Runs great!

I have basically close to the same set up as you. Switched to fed primers and have been 100% last 3000 rds

Thanks guys I appreciate the advice!

I’m getting ready to start loading .40 major on my Dillion 650. I will be using range brass. Is there any brands I should stay away from? I’ve heard pmc, just looking for some input. Thanks!

Hello, Ive been shooting uspsa production for the last few years, most recently I’m shooting a tanfo Stock 2. It’s an awesome gun. I’ve been wanting to shoot limited major next season, but haven’t wanted to spend the money on a new edge, or tanfo, mags etc. Recently I came across a deal that I couldn’t pass up. It’s a xdm 5.25 in 40 cal. It’s was sent to the Springfield pro shop and had action trigger job, 2lb 13 oz trigger. Narrow Dawson front sight installed, tungsten guide rod, Springer brass magwell, extended mag release, and six mags with Dawson base pads. The gun weighs 41.5 oz with a empty mag. I know the guy who shot it and it wasn’t shot a lot. It cost me about the price of a new 5.25. Looks like I’m gonna try out limited. I have no experience with 40 cal, hope I can shoot it as well as my stock 2!

Okay. Thank you. I knew that xdm’s had tight chambers. I was just wondering if any other xdm owners had trouble with .401 diameter

I recently acquired a xdm in 40 s and w to shoot uspsa limited with. What size coated bullets will I need? .400. Or .401. Thanks

I had it too on my stock 2. Took a file and got rid of it. Did not affect the gun at all. Sent from my SAMSUNG-SM-N910A using Tapatalk

Thank you very much! Sent from my SAMSUNG-SM-N910A using Tapatalk

Hello guys, I shot a scsa match today with my stock 2. When I got home and was wiping my gun down and checking it over I noticed that my rear sight has a slight amount of play in the dovetail. Is this normal. If not what to do. Thanks Sent from my SAMSUNG-SM-N910A using Tapatalk

Okay, Im sure this topic has been run in the ground but here goes. Ive been reloading for years, but at the moment I only shoot 9mm for uspsa. Around 10000+ rounds a year. Ive been using a square deal b for quite a while now. Ive been thinking about getting a xl 650. What do you all think? Worth it or not just for one caliber? Sent from my SAMSUNG-SM-N910A using Tapatalk

I get them occasionally, pitch it and go on. Sent from my SAMSUNG-SM-N910A using Tapatalk

Patriot Defense. Cdnn sports has large frame mags for 14 dollars. Sweet Pistol!

Im STOKED!!! Just put 250 rds through gun with zero malfunctions. A mix of federal, wolf, and winchester primers. Now to clean and polish! Sent from my SAMSUNG-SM-N910A using Tapatalk

Okay thank you! The gun seems to be working perfectly now! Sent from my SAMSUNG-SM-N910A using Tapatalk

Okay thank you! Ive been using flitz. Is that good enough? Should I use a more abrasive compound first? Sent from my SAMSUNG-SM-N910A using Tapatalk

Thanks for the info!! Sent from my SAMSUNG-SM-N910A using Tapatalk

Thanks for the info!! Sent from my SAMSUNG-SM-N910A using Tapatalk

I just finished my stock 2 tonight. I installed a 10 lb recoil spring, 13 lb hammerspring, eg extended firing pin, extreme one piece sear, bolo interrupter, daweson front sight, extreme titan hammer, cajun reduced power trigger spring. I polished alot on it, and had to fit the sear so the saftey would engage. Im getting 8lb double and 3.1 single. The only problem I have had is when I first started dry firing, the hammer wouldnt always drop on the reset on the first pull. It did it alot at first, but after a few hundred dryfires it seems to have stopped. Is this a break in issue? Thanks everyone for your posts and instructions! Sent from my SAMSUNG-SM-N910A using Tapatalk

Okay! I found it lol! On with the work!!! Sent from my SAMSUNG-SM-N910A using Tapatalk

My bolo interrupter did npt come with a smaller pin. What dp I do? Sent from my SAMSUNG-SM-N910A using Tapatalk

Okay thanx! I was kind of disappointed to see that. Im surprised it made it through qc. Sent from my SAMSUNG-SM-N910A using Tapatalk

While working up some loads for my new stock 2 tonight I noticed that my feed ramp has a sharp little notch on the side of it. If you run finger towards the chamber it feels fine. Away from it and its sharp. Should I take a stone to it? Opinions? Sent from my SAMSUNG-SM-N910A using Tapatalk