usmc1094
-
Posts
609 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by usmc1094
-
-
Not long they are a good company.
-
Check the dealer forum, he makes them. If i was still running my cr speed belt i would be buying a lot of them!
-
Thanks I'll give that a try.
-
QLS works fine on ELS belt if you only attach it with 2 screws. It is a smidgen of tetris but it works and the 2 screws hold it on just fine
Any way you could post a picture of that? I cant get mine on the belt without putting it at a 45° angle.
-
Could always attach it on just the upper.
-
I have to use a large taped up flathead screwdriver to pry mine out, and a rubber mallet to get it back in.
-
-
That sure is pretty!
-
Just got an email for the NRA World Shooting Championship, Presented By Magpul. Dates are September 24-26 at Peacemaker National Training Center in Glengary, WV
www.nraworldshootingchampionship.com
-
-
Look at the stoeger M3000 or the new M3K made for 3gun. Great gun for the money!
-
I have a 15 inch MI gen 2 (not the keymod) and have had no problems with it burning my hands. Maybe that one time at FNH when it sat on the table for an hour in the September sun.
-
You would only go to open if you use an offset red dot. Whay your running would put you in tac optics or whatever class 3GN calls it now.
-
Stoeger M3K 3-Gun Shotgun:
Just found this on YouTube.
-
Says April or so in Howards post.
-
The JM comp works, plain and simple. I have video of it on my rifle if you'd like to see. It is the only thing I have done to it, everything else is stock.
-
Is it going to come with a extended tube and any release date yet?
Jesse's post says it will come with a rebate or certificate for a mag tube. My guess is that it can't be imported with a extended tube.
-
No offense taken.
When I pull the bolt back, it locks, whether there is something in the magazine or not...
Ih, and as far as a manual of arms...I got this brochure telling me how to disassemble it. It didn't go too deeply into "proper operation".
I went to the Mossberg sight and saw the same "manual".
I believe they can improve on that...even maybe a video...it would be cheap and they could post it in a day with almost no cost.
it should only lock open if there is nothing in the mag tube.
-
Just pull the bolt handle, don't push the bolt release button. Give it a nice firm pull all the way to the rear and let it go. See if that helps.
-
^ thats what i was getting at. Mine does the same thing. Just charge the bolt and you should be good to go.
-
Are you pushing a button to release shells from the mag tube? If so what one?
-
I'll take them. Semper Fi!
-
Do the glock mags work with extended base pads like dawson or TTI?
-
This still appears to be a popular thread.
Today, another match, a different failure mode for failure to feed. Today was my second match and I completed 75% of the course (last time it was 50%).
I didn't have any double feeds this time, but with clay's in the air, I pulled the trigger and nothing happened.
I had no spring pressure pushing the shells out. I got home and pulled it out from the end. The spring was kinked and sort of distorted at one point. I'm assuming that it got caught up on the inside edge of the extension tube, where it mates to the magazine, but I can't be sure. The magazine extension is tight to the magazine.
What is the best way to fix that?
Until that happened, it appeared to run much better, with the ends of the piston rings 180 degrees out (there were lined up when I received the gun and shot it in the first match that way with 2 of 4 stages completed).
Thanks in advance for any advice.
sounds like it may have got twisted when you put the cap on. I would get a new spring, because once its bent there is a good chance that it will bend again. Bend the ends in more.
Stoeger M3000 Scattergun?
in Shotgun - Technical
Posted
I just put the OS on mine yesterday. It is right where the action bars are. I'll take a picture next time i make it upstairs.