[M&P full size sights ?]

I use 10-8 rear and Dawson FO front.

Sent from my ADR6425LVW using Tapatalk 2

[Need competition sight advice]

I use either the .125" or .140" wide rear sights with .100" wide front.

Sent from my ADR6425LVW using Tapatalk 2

[Need competition sight advice]

for Novak replacements, i like 10-8 sights. They make them to fit the S&W as well

http://www.10-8performance.com/s-w-1911-rear-sight/

for front sights, i like .100" wide Dawson fiber optic sights.

10-8 also has front sights for the S&W.

http://www.10-8performance.com/s-w-1911-e-series-front-sight/

[Question on XDM trigger comparing stock to trigger job or kits?]

I should add that he has over 25k rounds through the XDm that I sold him.

Sent from my ADR6425LVW using Tapatalk 2

[Question on XDM trigger comparing stock to trigger job or kits?]

I use Springer Precision trigger kits. When I used a lighter striker spring alone, the trigger was lighter, but felt mushy compared to the factory spring.

I've since sold my XDm to a friend, but he likes them so much, he's bought 2 more, which I installed SP triggers in.

Sent from my ADR6425LVW using Tapatalk 2

[S&A magwell and wilson etm mags]

They work fine for me.

Sent from my ADR6425LVW

[NE Ohio club USPSA match]

Flex, the website for the club is http://www.psfs-club.org/2.html

[magazine release cuts for SS]

If you want a huge relief cut, look at the 10-8 grips.

Sent from my ADR6425LVW using Tapatalk

[New 9mm Trojan Issues]

Wilson mags aren't magical. You can try Tripp followers in the Wilson tube.

Sent from my ADR6425LVW using Tapatalk

[M&P to get improved trigger?]

my guess is that it'll get the Apex FSS. Here's a post from Apex's Facebook page.

[RO front sight height]

Yep, that'll work, but i use a .100" (stock is .125")

[RO front sight height]

If you look at Dawson's site, it lists what front sights work with the different rear sights. IIRC, it's a .180" front that works with the adjustable rear sights.

[Can Only Use Stock Main Spring]

[2011 mags not falling freely]

good to hear.

[2011 mags not falling freely]

Front to rear tube dimension per Dawson mag tuning video is 1.370"

[2011 mags not falling freely]

You need to tune the mag. Some of the tubes are out of spec and can cause this.

[Hammer Bounce? After just changing MSH?]

[Hammer Bounce? After just changing MSH?]

The M/S cap is hitting the retaining pin before the hammer is down on the firing pin.

yep. the OP needs to either remove the cap pin, or get a new cap and spring.

[First Round Flyer]

just a guess, but maybe its how the first round is chambered (using the slide lock vs. pulling the slide back) and how the barrel locks up.

[Anyone shooting the STI Tactical?]

I carry a 4.15 Tactical in 9mm. no problems at all and is just as nice as my Edge. I went to the range the other day and let a friend shoot it. 4 of 5 shots were touching and the one that wasn't was his fault. he's an XDm shooter and shit better with the STI.

Sent from my cyanogen modded incredible

[Davidsons grips, still available?]

Is that the same grip that's on the TRP Springfield.

Yes...Larry makes the G10's for Springfield

Sent from my ADR6300 using Tapatalk

[Old Race Guns]

finally picked up the Nastoff built gun.

[CZ's in Southern Ohio Area]

You should be a few hours from Buds in Lexington.

[Top Shot Season 3: Episode 12]

The difference was, Dustin Is an all-around shooter, while Mike is mainly a pistol shooter.

[5" Iron sight setup for my SS Springfield]

i use .125" rear (10-8) with a .100" front (Dawson).

this photo is fairly close to what i see.