atbarr
-
Posts
2,008 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by atbarr
-
-
Why not, I sure did.
-
Give Brian a call, he will not over sell you.
-
This is with the Dawson adjustable rear, not sure about the fixed rear. The front mounting hole is the same.With Dawson, the 17 front sight is .285, on the 34, it's .300 in height.
-
Sure it can, if you want to be moved to Open. Ask me how I know.DOH are not allowed in Single Stack division
-
With Dawson, the 17 front sight is .285, on the 34, it's .300 in height.
-
The case gauge means nothing. The only sure check, is dropping each one in your barrel's chamber. YMMV
-
Extended http://www.shootersconnectionstore.com/Glockworx-ZT-Tungsten-Guiderod-Extended-P1997.aspx
That's what I figured, but when I looked up guide rods at a few sights, they had the G17 and G34 listed with the same part numbers. Thought that was bizarre but not impossible depending on how glock designed it... like I said, I don't have a G34 to disassemble to check.The G17 guide rod will not work in the G34, too short.
Standard http://www.shootersconnectionstore.com/Glockworx-ZT-Stainless-Steel-Guiderod-P1998.aspx
-
The G17 guide rod will not work in the G34, too short.
-
Then that's all that matters.They fit fine, actually.
-
How do they fit in your chamber? That is the ONLY true check.
-
Wow! Didn't know that.Did a quick Google search and found that Loctite is only for metal to metal contact... It will supposedly eat into plastic... Not good...
-
You can remove them, even using med. Lock-tite.
-
I carry a G36, nice and thin. 6 + 1 is more than enough. I use an IWB Razor, I don't even know I'm carrying it.I would carry a Glock and its just alittle wide and not as comfortable.
-
You can put in a stiffer mag release spring.
-
Bell enough to seat the bullet. Will the cartridges drop in and out of your chamber?
-
Just another, 'Because I say so rule'.
-
At least with the large primers, skip the Dillon tube, drop in your press.
I just got straight into the Dillon tubes. You have to hold them just right but it works like a charm for me. Small and large primers.
-
-
The primers would jam or be upside down, while entering the tube. I tried several times, but same results.
What problems have you had with small primers? I was just about to buy one and held off when I read your comment.I love mine with Large Pistol, I've gave up on using it for small pistol.
-
I love mine with Large Pistol, I've gave up on using it for small pistol.
-
Amazing!
-
After the popper falls, there is no recourse.
-
I'm sending the upper to Shaun Hopkins, to pin it. Without a front sight, so far I've shot the most points in stage 10. Of course I also have the largest time. LOLDid you get that front sight fixed?!
Thanks for asking Eric.
-
Just wondering, can you look in each case, before the bullet is placed in it?
Dillon XL 650
in Dillon Precision Reloading Equipment
Posted
When I started I told Brian I wanted a 650 with a case feeder. We talked for a few minutes and he told me I didn't need a 650. He said if I had to buy a 650, to go to Dillon. Since he was saving me several hundred dollars, I went with the 550. Right now I probably average 2,000 rds. a month. Brian was right, the 550 was the correct press.
Just talk to Brian.