-
Posts
7,200 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by eerw
-
-
If you can finds a standard TS , will put in about the same place trying to make a shadow 2 capable of shooting 40sw.
-
AO1 LD Review
in CZ
-
AO1 LD Review
in CZ
6 minutes ago, lfine said:Think the only other thing I want to do at this point is change out the rear sight (at least) to have more of a sight picture like my Shadow 2. A lot of room for me right now for the front FO to float around in. Do we have the specs on the sights for A01 and which can be used to replace either front or rear?
Rear dovetail is a low mount cut.
rear sight is .365 high.
-
32 minutes ago, Stafford said:
Those are factory pistols, correct?
How good are the triggers on those without the Custom treatment?
Da is in 9# range. A set of springs will do a lot for you. And short reset disconnector if you really want it.
-
Got some good prices on SP01 Shadows now at CZC.
-
AO1 LD Review
in CZ
1 hour ago, lfine said:Just got my LOK bogies. Fit great. And my extended safety - will need a little filing to make the safety engage. So what's the route to take for replacing the hammer spring on this?
can you send me a photo of the bogies on the gun. Thanks -
^^^
check pretravel and overtravel adjustment screws
about the only thing that will mess you up.
-
Phantom is single side decocker. No rhs lever.
-
1 hour ago, gunner01 said:
Leaning strongly towards CZC plate cut. Roughly, What kind of lead time are you running right now.
Is the direct mill cut the same depth as the plate cut, so in effect you gain exactly the height of the plate when using an optic with the plate?
We are at about 6-7 weeks .
the plate forms the top parts of the FP channel so it is about as low as direct milling is.no trouble on transition between dot and iron sights
-
CZC offers the RDS plate cut, we can also direct mill for the optic too.
right now my primary is RDS, my backup is direct milled.
-
11# or 12# will give you a lighter DA pull. Depending on primer, seating depth. Worse thing will be light strikes.
-
AO1 LD Review
in CZ
Texture is same as standard A01 grips.
will run CZ 75 10, 15,16,17,18 and 19 end mags
-
On 10/20/2019 at 12:36 AM, slavex said:
Hmmm, hadn't swapped sears, I will try that. thanks
sear doesnt do anything in the DA stroke.
DA is the disconnector coming off the trigger bar -
AO1 LD Review
in CZ
-
DPP Screws
in CZ
Should be an M4
M4 x .7 x 15.8mm
-
On 11/5/2019 at 12:07 PM, Slalom45 said:
Expected to see JJ shooting Prod at locap nats. Anyone know why he's not there?
Philippines , prepping for Australasia Match
-
Just need an RMR plate.
tough thing will be finding one. The P07/P09 dovetail is hard to mill a dovetail plate for as the dovetail is cut not equally on either side.
-
On 10/26/2019 at 4:56 PM, Superpipe9 said:
Stuart is that based off a TS? Who made the comp? Thanks
It’s built on a CM
The shop guys built a one off comp
-
-
at the NAGSW Expo in Orlando
-
Sounds fun! Great project.
-
AO1 LD Review
in CZ
1 hour ago, lfine said:Any more footage of it in action coming up anywhere? There's very little out there and i'd like to see some more before I might buy one.
Also, Stu, any idea how close we are to getting it USPSA Production approved? Hit the 2000 mark, etc?
Thanks, I'm looking forward to getting one.
I havent checked numbers in awhile. See what I can find out.
-
AO1 LD Review
in CZ
7 hours ago, yigal said:nice TV
Surprisingly not as bad as you would think.
-
AO1 LD Review
in CZ
AO1 LD Review
in CZ
Posted
yes