[XL750 or RL1100?]

[New to reloading, have some questions re: 9mm major]

Good plain.   HS 6 will be dirty at true 125-135 minor loads. If you go to 140-150 Power Factor.( factory Self Defence PF) It cleans up quite well. and You may get a little use of your comp.

[Glock MBX Mags]

Any body else notice all(mose) the problems. With aftermarket enhancements. Magazines, Triggers and guide rods for example. Primarily involve the gin 5.???

 

[Sport Pistol - Temperature Sensitivity]

20 ish fps

[New to reloading, have some questions re: 9mm major]

2 hours ago, ysrracer said:

 

Agreed, I just said, I've never heard of it. It's a pretty specialized round. 

 

Just like most gun shops don't carry .257 ackley improved. I've never seen it, but it might be out there.

Everglades ammo / bullets. In Florida does or at least did offer. 9 major ammo.

[New to reloading, have some questions re: 9mm major]

I would check that ammos OAL before buying a bunch.

[New to reloading, have some questions re: 9mm major]

56 minutes ago, ysrracer said:

OP, stop. You're in over your head. Find someone that can help you in person.

Agreed also . Having "worked" with two CZ open guns with unthroughted chambers. He is Two plus grains over what is needed to make 170 power factor. And well into primer popping territory. Which is just under parts flying territory.

[Dry Lube for dies?]

hear is one under a different brand

https://www.jdindustrialsupply.com/topcote.html?utm_source=bingshopping&utm_medium=cpc&utm_term=topcote&utm_campaign=cse&msclkid=0efa9372620a1181a355f29c88bf846b

[Dillon 1050 spitting out primers]

I can feel it .If I have the swage set. yes it is a spongy feeling.

[Wet tumbling solution]

just asking because clays is the only powder . That I know of that reacts with Hornady one shot. Had the same issues. Plus a lot of failures of the powder to fully burn. never had the gummy residue. My procedure at that time was to load as much ammo as I could in the cold months.

Went back to Bullseye powder and some N310. All the issues went away. This was when I only shot Bullseye competition and skeet.

[Wet tumbling solution]

41 minutes ago, Hammbone said:

I've used One-Shot. In fact, it was my exclusive go-to way to lube. I would put a couple squirts into a 1gal zip lock bag, put in the brass, the shake and tumble for a couple minutes. The problem I had is that after about 6mo, some loaded ammo got sticky and I had some FTF issues with my 1911 45acp. After some investigation I noticed the insides of the mags were very gummy. For now, I assume the one-shot caused this? Can't prove it.

Right now what I'm doing is, and it's a huge PIA, is after done in my brass drier, I put the brass in a dry media tumbler with clean corn cob and mineral spirits.

clays powder?

[Dry Lube for dies?]

start hear then proceed. This should help you identify the product. This is only one of a few. At one time you cold get just the lube.

https://multimarketingco.com/tool-surface-lubricant/

[any AR experts?]

When you push on the firing pin. Will the tip come through the firing pin hole?

[Dillon 1050 spitting out primers]

Only time I have had a primer detonation. Was a rung primer. Wasn't using the swage at the time. After that always used the swage.

Now all brass is "processed". Puts an end to all kinds of problems.

[Dry Lube for dies?]

Hornady one shot. Is actually a saw blade lubricant. That's rebranded. Do a little research. The info is out there.

When I did. Found that the Hornady was/ is. Less expensive for me to get. Others may find the wood working

Version. To be less expensive.

[subsonic 9mm suggestions]

The 115s will still have a"crack" when fired. A 147 or 160 at 900 fps. Will not.

The altitude, temperature and humidity . Have less true effect. Than what the

Charts imply. If you want subsonic it has to always be low enough . No matter what the

Temp, humidity, altitude is. 

[Dillon Automation]

3 hours ago, Kema said:

Video is not even visible without logging to Vimeo. Maybe Dillon needs some help to actually host video in their own servers

 

the link provided above works fine.

[Pull Weight Seems High on New P80 Build, Where Did I Go Wrong???]

The after market part . Was junk. That's why a lot of people say not to change parts. I don't fully agree with that. Buy have seen that all parts are not created equal. Some are down right trash.

[Accurate Nitro 100 NF vs Ramshot Competition (9mm)]

Nitro 100 was one of the worst powders I have tried in pistol. Very inconsistent. Dirty just would not burn. Velocity swings. Shall I continue? RS Competition is a powder I've never tried.  If you like it . Can get it. That would be the one to use.

[Accurate Nitro 100 NF vs Ramshot Competition (9mm)]

nitro 100 says this

For centerfire metallic cartridges please use load guide version 3.5 or later.

[Accurate Nitro 100 NF vs Ramshot Competition (9mm)]

is this what you are after it list one pistol loading in 9mm.

https://shop.hodgdon.com/ramshot/ramshot-competition

[Pull Weight Seems High on New P80 Build, Where Did I Go Wrong???]

Coffee should be Hot, Black and Bitter.  So yes that is a  cup of milk. 

[Dan Wesson DWX: The Mother Thread]

1 hour ago, 18111811 said:

we have come close to being able to ship the DWX multiple times, but each attempt has been met with obstacles and set-backs along the way.

this statement. implies the product is ready . no boxes  to put them in would be a reason for example.

[Dan Wesson DWX: The Mother Thread]

After reading this. One gets the impression that there are guns ready to ship.

So why not ship them?

[Pull Weight Seems High on New P80 Build, Where Did I Go Wrong???]

A lot of pull weight . Is in the striker spring. 4.5 pound gives me the best. Ballance of pull weight and reliability.