[Xtreme Heavy Plate Bullets and AET barrel]

My aet barrels will not group well with extreme plated. I tried different crimps, over all lengths, 165 and 180s, and different powders with no success. 1 in 10 goes through the target side ways. They aren't even good enough to practice with.

Lead, Polly coat and jacketed are very accurate.

Having said all that, extreme plated shoot great in my standard twist barrels.

[To lock back or to not lock back]

My limited guns are set up to lock back in case I ever decide to shoot L10.

[Smileys in .40]

I get a similar mark on ejected rounds. I believe the bullet is striking the slide somewhere while ejecting.

[Coated shoot softer than jacketed at equal MV?]

You have to look at it from a work stand point. The same amount of work is done, with more or less powder depending on the bullet seal in the barrel.

[Spent primers?]

I dump my spent primes in empty power jugs.

All I need to do is find a scrap yard.

[SVI 9mm Major Load Data]

I like HS6 and autocomp for 9 major. I get less dot movement with HS6.

[First Case Failure - 9 Major]

It is interesting that is seems like a clean cut. I had a 1911 fire out of battery and it was a ruff tear.

[odd primer problem]

I have had this issue when depriming 9mm cases. The case hangs up in the press. I assume hot loads.

[odd primer problem]

I have had this issue when depriming 9mm cases. The case hangs up in the press. I assume hot loads.

[Magnum pistol primers vs regular pistol primers]

I get more consistent velocities with SPM primers. They burn hotter longer. If I remember correctly, the are about 5-10fps faster than standard primers.

[CZ Tuning 101 with Professor Atlas]

I backed the trigger over travel screw a 1/4 turn and it works! I guess the double action needed just a hair more travel.

[CZ Tuning 101 with Professor Atlas]

If I pull the trigger quickly, the hammer will fall in double action. If I pull it slowly it will cock but not fall.

[CZ Tuning 101 with Professor Atlas]

I installed the CGW disconnector but now the hammer will not fall in double action. Single action seems fine. If I press down on the sear cage while pulling the trigger in double action, the hammer will fall. Any ideas?

[Thumb safeties.]

I shoot with my thumb on the saftey so it can't pop up.

[Fiber optic sight recomendation.]

I like the Brazos lightning rod. The fiber is always the same size and intensity regardless of orientation to the sun.

[Super 1050 How much time? Going from 9mm to 45ACP]

Would I be best served with two, one for 40 and one for .223? I am mechanically inclined and youtube videos are a great resource.

[Comments on difference in primers for 38 Super Comp]

I get more consistent velocities with small pistol mag primers. I assume they are burning all of the powder.

I haven't tried small rifel mag yet. I would expect similar results.

[Super 1050 How much time? Going from 9mm to 45ACP]

I am thinking about getting a 1050 to load 40sw and to process 223 brass. How long to swap between the two?

[Tumbler advice]

I wet tumble with turtle wax car wash. The cases come out shiney with a slippery coating. Loads smoothly in my press.

[Single Stack Nationals Stages]

The match should have had at least one 32 round field course.

People that wear suspenders don't like running

I dont wear suspenders, or kilts.

[Single Stack Nationals Stages]

The match should have had at least one 32 round field course.

[1050 - advantages of buying new?]

I am thinking about getting a 1050 for loading 40SW and processing .223 brass. How much of a pain is it to switch back and forth between the two?

[How long does your local USPSA match last?]

1-3pm depending on the number of shooters and stage reset.

[Anyone use .40 across the board for Open, Ltd, SS?]

I am thinking about this for limited, SS and production. Minor for production.

[SS Nats]

It was rain free Saturday.