-
Posts
234 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Aric
-
-
My simple blued IMM that I put a deposit on December 2017 shipped yesterday. I also put a deposit down on a kooky bull$hit, custom cuts, pink glitter with unicorns IMM gat and I haven’t heard anything from SV about it.
-
I thought you sold your open gun.
-
5 hours ago, levellinebrad said:
If mine is ready in February it will be 14 months. I’m expecting March though. What are you shooting now? I thought it was an SVI in 38. I know it’s loud!
9mm so I don’t have to chase brass.
-
Mine is waiting on final payment and FFL. About 12-13 months for me.
-
I am not sure if I am any faster but I feel like my grip is more consistent with one.
-
My AET barrels liked everything except plated.
-
Any new info on the KKM barrels?
-
I ordered mine last December, also. Last week they said they were ready for my scope.
-
Check the diameter of the projectiles. A few years ago I got a batch that had .399 bullets. I contacted the manufacturer and they said it’s was within spec. They were not accurate and had about the same tumble rate as yours.
-
I found out that mine functions perfectly with two.
-
The screw isn’t present on the UBR 2.0.
-
-
Has anyone tried to install a Magpul UBR 2.0 stock on a MPX with a KAK adapter? If so, how did you prevent it from spinning on the buffer tube? It comes with a piece that would prevent it from spinning on an AR type rifle, but here is no where to mate on a KAK adapter.
-
Is it possible to buy a gen 1 bolt from SIG?
-
A 9mm case full of 3n38 has a nice recoil in my gun. A zip tie in my 1050 stopped powder spillage.
-
I have this same failure. However, my rate is lower than yours. When everything is clean, it seems to happen less often. Debris from de-priming finds its way into the priming arm and the primers don’t sit flat any more.
I am fairly sure this is the culprit as my 1050 is 99.99% on priming.
-
-
I have two that don't fit and they barely go into the grip before I hit resistance.
-
I have two STI magazines that do not fit into one of my SV steel grips. They work in my other SV steel grips. I think it weird that they fit in three other steel SV grips, but not the fourth.
-
I couldn't notice a difference between sorted and un-sorted in 40 major or 9 minor. However, I could feel a difference with sorted brass in 9 major. If you can't feel a difference and they all make power factor, it isn't worth sorting.
-
Has anyone been able to fix STI mags that stick in steel grips? If so, what did you do?
-
I have more 170's than 140's. My logic is: I drop 170's and they are more likely to get damaged or dirty. My 140's almost never touch the ground.
-
1 hour ago, jimbullet said:
interesting - my oal off the press does give me slightly different OAL from 1.158 (which is what it was meant to be set up to) to as long as 1.170; randomly when all stages of the press is full.
I tried to put only one case and get it through the entire 4 stages of the press before putting another and this is when I get more consistent OAL exactly to what it was meant to be at 1.158. The press is an SDB, scratching my head as to why and how to solve that.....
When I am done loading, I stop leaving brass in each station. That way when I start loading again I don't have shorter arounds until all the stations are loaded.
-
How consistent is your oal? Are you using the same head stamp?
I was loading my 40 at 1.20. However I was getting a large velocity spread. I changed my oal to 1.185 and my velocity spread came down to 10fps+\-. I chambered Several rounds and then measured their oal. The oal's were all shorter after clambering. I think at that length, there wasn't enough purchase on the projectile.
SVI wait time
in Open Pistols
Posted
Apparently Texas got snow and ice yesterday and fedex isn’t running. Should have it on Tuesday. I’ll post photos when it comes in.