Jump to content
Brian Enos's Forums... Maku mozo!

mpom

Classifieds
  • Posts

    749
  • Joined

  • Last visited

Posts posted by mpom

  1. 10 hours ago, kurtm said:

    J. P. Would be my choice....but it's not on your list.

     

    Agree, a JP can be set up to be super crisp, as in no takeup, minimal to imperceptible travel and no overtravel, reset is about .03".

    Plus with hardened components, does not change over time. Does take some time to install and adjust. 

  2. Also running Glock striker springs, no noticeable increase in trigger pull weight, probably because in the M&P the trigger pull only rotates the sear, does not push striker back compressing striker spring, unlike the Glock system, which does further compress striker spring.

    Wolf 5.5 or 6lb Glock striker springs usually available from Brownells, or Wolff directly.

  3. If the loaded cartridges enter and fall out of the case gauge without effort, would not worry about rotation, think they will enter and fall out of the barrel when firing.

    Just test fire before the match.

    Mark

  4. Well, at the sale price for the new 135 gr bullet I ordered some, .357 diameter,  will hopefully play nice w the Apex barrel in my M&P and the OEM S&W barrel in another pistol.

    Reasonable shipping charge makes it a no brainer.

    Mark

  5. A couple of things I would check while waiting for the gas tube to arrive: is the gas key showing signs of gas blow by as would happen if its 2 bolts were loose?

    Do the bolt rings pass the stand up test, where you pull the bolt out and stand the assembled bolt carrier group on the bolt? Bolt should not collape into BC if rings are good.

    Does the action operate smoothly when pulling charging handle back fully and lock into battery when CH is released slowly? Similar force required compared to another rifle/carbine?

    Does BCG move freely with upper separated from lower?

    Something is not right and I feel your frustration at trying to solve the issue 😕

  6. Doubt it's the muzzle device. 

    Gas tubes are cheap, worth replacing, especially if old one has high round count.

    If rifle runs well and locks on empty w original gas block, and empties are ejected between 3 and 5 O'clock, then I would call it good as you really dont want less gas then that.

    So basically you are out the cost of the AGB.

  7. Now that you have the gas block alignment sorted out, I would look at the action spring and buffer. Are you sure the rifle length one is "normal" strength and not "extra" or "plus" strength?

    Also, if this is a race gun rather than an alll purpose home defense/race gun, a lighter weight buffer would reduce reciprocating mass and rifle movement during recoil.

    Since the rifle ran well with 223 ammo with the non adjustable gas block, wonder if there is something wrong with the SLR, as WFO it should mimic the fixed one in gas flow.

    What does SLR say?

    Most important, personally would not run the gun with carbine buffer and spring as gas key might impact the upper receiver in its rearward travel.

  8. Sounds like there is no dimple on the bottom of barrel to help center the GB over the gas port, so you need to find a way to center it. 

    Hole in gas block should always be larger than gas port in barrel. Pencil lines parallel to bore bisecting the gas port and gas block opening is how I line up the gas block to get concentric matching of holes. Cannot tell from photo but it's possible gas block is covering a small portion of gas port.

    No stiction or deflection of end of gas tube entering gas key on bolt carrier, and inside of gas tube clear?

    Mark

  9. Check the gas port diameter, if the gas block is sitting properly (coaxial circles surrounding gas port) and the gas tube is totally clear and seals well against gas key.

    Not sure of current recommendations on rifle length gas port diameters, but not hard to find on M4carbine.net.

     

    Mark

  10. Thanks BD, that info is helpful. I really like the new BTR reticle called ASTR4. if you helped design it, congrats!.

    Currently running a Burris RT-6, my 1st 1-6 power scope and wonder if the PST and BTR gen 2s have better glass?

    The RT-6 has some fisheye @ 1 power and the reticle is a bit busy for my taste, so curious if the other 2 are a step up in optical quality since they are also more expensive. 

    Mark

  11. Has anyone compared the Midas BTR gen 2 1-6 to the PST gen 2 1-6?

    Seems like a fair comparison as they are close in price. I can tell from the specs/online info that the Vortex is a bit heavier, has a smaller center dot and made in the Philippines vs China, but would appreciate any feedback on differences in clarity, brightness or other optical quality.

    Thanks in advance,

    Mark

  12. Think the blow out price on the Athlon Midas BTR 1-6 is because a new version, Gen 2, is coming out.

    Makes the budget scope choice even more difficult 😲

    Gonna stick with my Burris RT-6 till something is out that is significantly better at less than twice its price.

     

    Mark

  13. 21 minutes ago, bigfish said:

    I did try an extra power Glock striker spring in mine and it worked fine for about 2 months and then the striker broke.  When back to the original.  Bad striker or too strong of spring? Not sure what caused it

    Which part of the striker broke?

    No issues with thousands of cycles on my striker, Wolff extra power striker spring.

     

    Mark

  14. Of course it feels good to help develope new shooters, glad to be of service!😀

    On a separate note, wonder how the bullet diameter of .355 which is standard with 9mm Blue Bullets, does not negatively impact accuracy in a typical 9mm pistol.

    Would love to try their 124 or 135 bullets, but wonder if the smaller than typical diameter is a plus or negative wrt to accuracy. Have asked BB by email, so far no response, though its the weekend.

     

    Mark

×
×
  • Create New...