JBeach Posted July 7, 2009 Share Posted July 7, 2009 Started loading my .38 spec. with 5 gr of IMR 4756 (since I have it on hand from shotgun reloading) and a 158 gr .358 wadcutter. The IMR data center said col of 1.475. That col length made the bullet look lopsided. Too much out front. Shot almost like a .22 with small report, a weenie sounding load. I ramrodded the barrel (Colt King Cobra at least a 6" barrel) to make sure it didn't squib. When I unloaded the cases from the cylinder there was unburned powder. I didn't have the chance to chrono it yet. My questions are: How much more should I stuff the wadcutter down into the brass. Why is the col (listed) too long? I'm sure I'll have more questions when I get some feedback. Thanks, JB Link to comment Share on other sites More sharing options...
Jim Rusert Posted July 7, 2009 Share Posted July 7, 2009 Most of the .38 WC loads (including my own) I've seen have the bullet pretty much even with the end of the case. Link to comment Share on other sites More sharing options...
JBeach Posted July 7, 2009 Author Share Posted July 7, 2009 (edited) So what about the col? Is this length a max? What about pressures? I'm still confused. If col is so important, why in my load will the bullet be so far into the case. I'm doing a search and try to learn more about col. JB Edited July 7, 2009 by JBeach Link to comment Share on other sites More sharing options...
bball97 Posted July 8, 2009 Share Posted July 8, 2009 So what about the col? Is this length a max? What about pressures? I'm still confused. If col is so important, why in my load will the bullet be so far into the case. I'm doing a search and try to learn more about col.JB I ran into the same thing. I started seating the wadcutter with the beveled end just barely sticking out of the casing. Much better performance with less air in the casing. Sure looks funny that deep, but I believe that is how they are made to be loaded. My most accurate load was 3.1 grains of W-231 with a 148 grain double ended wadcutter in 38 special. Link to comment Share on other sites More sharing options...
bball97 Posted July 8, 2009 Share Posted July 8, 2009 So what about the col? Is this length a max? What about pressures? I'm still confused. If col is so important, why in my load will the bullet be so far into the case. I'm doing a search and try to learn more about col.JB Just a thought, was the 158 grain listed as a swc? (semi wad-cutter) That would stick out of the casing like a normal bullet. Link to comment Share on other sites More sharing options...
jasond Posted July 11, 2009 Share Posted July 11, 2009 Where is the mouth of the case compared to the cannelure (crimp groove)? Link to comment Share on other sites More sharing options...
David Sinko Posted July 14, 2009 Share Posted July 14, 2009 I don't have much experience loading the full WC bullet in .38 Special, but if I were you I'd try a different powder and yes, the bullet WC should be seated about flush with the case mouth. That SR 4756 powder has a well deserved reputation for reaching 1100 FPS with 158 gr. cast bullets in the 2" S&W J Frame revolvers. This is good to know in case you ever had aspirations of shooting .38 Major with your Model 60. Dave Sinko Link to comment Share on other sites More sharing options...
JBeach Posted July 14, 2009 Author Share Posted July 14, 2009 I'll have to load one more and shoot a pic of it for the point to get shown, but I did find out that I was using data from a lead semi-wadcutter instead of a double end wadcutter. So what would a col be on the dewc? We allowed to post pics? Jerry Link to comment Share on other sites More sharing options...
jasond Posted July 15, 2009 Share Posted July 15, 2009 COL of DEWC or HBWC is flush with case mouth. Hornady's online data says 4.0 of 4756, but I'd try a faster powder. Link to comment Share on other sites More sharing options...
JBeach Posted July 15, 2009 Author Share Posted July 15, 2009 I've got a bunch of 4756 as well as clays (haven't checked if this is even an appropriate powder yet). I want to see if it is shootable in my .38's (spec.). Just don't want to have too many powders to store (and buy). I'll back the load back to 4gr. and load to case end or just a little longer and then chrono. Thanks for the help. Jerry Link to comment Share on other sites More sharing options...
Tom E Posted July 15, 2009 Share Posted July 15, 2009 I've got a bunch of 4756 as well as clays (haven't checked if this is even an appropriate powder yet). I want to see if it is shootable in my .38's (spec.). Just don't want to have too many powders to store (and buy). I'll back the load back to 4gr. and load to case end or just a little longer and then chrono. Thanks for the help.Jerry 158 wadcutters are kind of unusual. You're on the right track. Normally you add powder until it burns efficiently (doesn't leave excessive unburned powder) and if that doesn't happen before you reach a reasonble pressure/velocity for the round, you go to a faster powder. Since you have Clays, it would probably be the better choice for target type loads Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now