Smokecloud Posted February 26, 2007 Share Posted February 26, 2007 I am getting ready to build a new Limited race gun in .40sw. Looking at STI frame, Bar-Sto bull barrel and Caspian slide. I have spoke to a couple of people about the various barrel ramp cuts and their pros and cons. What is the preferred method here with you guys? Seems like the STI mostly offers the Nowlin/Wilson cut more than the Clark/Para cut. When I look at barrel selections to match them up, I noticed that Bar-Sto also offers the "Bar-Sto" cut for their ramp, but I have yet to see a frame offered for that cut. I have emails into Bar-Sto, Brownells, STI and various others, but of course email is slow and I dont have any replies as of yet (about a week). Im thinking of just ordering the Wilson/Nowlin cut for both barrel and frame. Oh, another question, does anyone know where a Bar-Sto barrel might be in stock? I know what the wait game is like for one of those. I have checked with midwayusa, Brownells and speedshooter.com, but they all do not seem to stock that particular barrel at this time. Thanks guys. Link to comment Share on other sites More sharing options...
Flexmoney Posted February 26, 2007 Share Posted February 26, 2007 Have you tried a search for this info here on the forum ? This one comes up every so often and past thread should help out. Link to comment Share on other sites More sharing options...
HSMITH Posted February 26, 2007 Share Posted February 26, 2007 The Clark/Para ramp is the way to go if you have a choice. It is stronger than the W/N. Link to comment Share on other sites More sharing options...
gans Posted February 26, 2007 Share Posted February 26, 2007 Be careful when getting a Bar-Sto barrel. If you want a barrel with shallow locking lugs for tight lock up, their barrels don't have them unless you get the marine corp cut. Link to comment Share on other sites More sharing options...
wide45 Posted February 27, 2007 Share Posted February 27, 2007 Go to http://www.schuemann.com/ select AET information Scroll down to Ramped and Unramped barrels. Read up. Link to comment Share on other sites More sharing options...
born-in-45 Posted February 27, 2007 Share Posted February 27, 2007 You might try Brazoscustom.com (or 1911store.com) as Bob sells Bar-Sto barrels. Link to comment Share on other sites More sharing options...
Mistral404 Posted February 27, 2007 Share Posted February 27, 2007 Virgil Tripp is a wealth of information. Talk with him sometime. Most gunsmiths will agree the C/P has more surface area. I generally stay with the C/P because my smithy likes it best. There was a time when you could get a Nowlin in C/P cut but that has changed. Schuemann is now my barrel of choice. Link to comment Share on other sites More sharing options...
Carlos Posted February 27, 2007 Share Posted February 27, 2007 Virgil Tripp is a wealth of information. Talk with him sometime. Most gunsmiths will agree the C/P has more surface area. I generally stay with the C/P because my smithy likes it best. There was a time when you could get a Nowlin in C/P cut but that has changed. Schuemann is now my barrel of choice. Agreed. don't need the special cutter for a C/P - just normal endmills. Schuemann is the MAN. Link to comment Share on other sites More sharing options...
Smokecloud Posted February 27, 2007 Author Share Posted February 27, 2007 Thanks for all the reply's. I am learning a lot. I also just got a email from STI, they apparently do not offer the clark/para cut in their frames, so If im going to go that route, looks like I would have to buy a SV frame. I havent had much time to read up yet. Internet problems and two kids in diapers, but they will goto sleep sometime today and hopefully my net will still be working when they do. Link to comment Share on other sites More sharing options...
XRe Posted February 27, 2007 Share Posted February 27, 2007 Someone correct me if I'm wrong (I'm sure you will ), but any competent gunsmith can cut an STI frame for a C/P ramp, correct??? Simple operation w/ an endmill??? Link to comment Share on other sites More sharing options...
HSMITH Posted February 27, 2007 Share Posted February 27, 2007 Dave, it is a pretty simple operation. It only takes one set-up in the mill too which is nice. The VERY basic version is you cut a notch for the feed ramp of the barrel to fit in and stick through, then make another cut below for the lug. The cuts are different sizes, so you need 2 endmills or equipment that will compensate for the different sized cutters. With 2 endmills and a knee mill it is a really simple operation. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now