MoonJeong Posted August 31, 2018 Share Posted August 31, 2018 Any recomendations for 100 grain round nose load for steel challenge? I have w248, longshot, aa7, hs6, sport pistol, autocomp for poweders. Dont have to much time for load dev anymore. Its on an akai open gun. Thanks! Link to comment Share on other sites More sharing options...
Wvaughn7 Posted August 31, 2018 Share Posted August 31, 2018 I just run the 100 RNFP Xtreme bullets on top of my normal major load of 8.0 grains of HS6 and Have had good luck. This load went a little over 135pf out of my gun and was very flat. Recoil was a little harsh for a barely minor load, but it was a dream shooting them back to back with my major loads. Link to comment Share on other sites More sharing options...
MoonJeong Posted August 31, 2018 Author Share Posted August 31, 2018 Thanks will try that. 1 minute ago, Wvaughn7 said: I just run the 100 RNFP Xtreme bullets on top of my normal major load of 8.0 grains of HS6 and Have had good luck. This load went a little over 135pf out of my gun and was very flat. Recoil was a little harsh for a barely minor load, but it was a dream shooting them back to back with my major loads. Link to comment Share on other sites More sharing options...
ProfessorGascan Posted September 3, 2018 Share Posted September 3, 2018 On 8/31/2018 at 9:42 AM, Wvaughn7 said: I just run the 100 RNFP Xtreme bullets on top of my normal major load of 8.0 grains of HS6 and Have had good luck. This load went a little over 135pf out of my gun and was very flat. Recoil was a little harsh for a barely minor load, but it was a dream shooting them back to back with my major loads. Did you have any problems with accuracy with this load? I was under the impression that xtreme plated bullets had a speed limit of 1200 fps. I use these bullets over 4.4gr of Titegroup which cycles my three factory pistols reliably. Link to comment Share on other sites More sharing options...
Wvaughn7 Posted September 4, 2018 Share Posted September 4, 2018 11 hours ago, ProfessorGascan said: Did you have any problems with accuracy with this load? I was under the impression that xtreme plated bullets had a speed limit of 1200 fps. I use these bullets over 4.4gr of Titegroup which cycles my three factory pistols reliably. It's not the most accurate load I’ve ever shot by any means, but it’ll hold 3-4” at 25 yards out of the cheaper lone wolf barrel in my open Glock resting off my elbows. I’m not a great pistol bench shooter so I would expect some of that is me. I used them for steel challenge only which didn’t need any crazy accuracy and they worked for me. Link to comment Share on other sites More sharing options...
kneelingatlas Posted September 4, 2018 Share Posted September 4, 2018 On 8/31/2018 at 4:03 AM, MoonJeong said: Any recomendations for 100 grain round nose load for steel challenge? I have w248, longshot, aa7, hs6, sport pistol, autocomp for poweders. Dont have to much time for load dev anymore. Its on an akai open gun. Thanks! 10gr of AA7 under a 100gr bullet will make you smile Link to comment Share on other sites More sharing options...
MoonJeong Posted September 4, 2018 Author Share Posted September 4, 2018 Will have to try that one! Link to comment Share on other sites More sharing options...
MoonJeong Posted September 6, 2018 Author Share Posted September 6, 2018 What is the consensus (if there is) on slow vs fast poder for minoridad in open? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now