rootacres Posted April 7, 2017 Share Posted April 7, 2017 (edited) Does anyone have any pics with measurements showing how much they took off to make work? I am going to try to do this once without messing it up. Are the FPB even tested at Level 2 matches to ensure they work? I have a titan hammer, xtreme 1 piece sear, and a bolo. . Xtreme FP Edited April 8, 2017 by rootacres Link to comment Share on other sites More sharing options...
MemphisMechanic Posted April 7, 2017 Share Posted April 7, 2017 (edited) 90% of the people out there don't make any adjustments to the block for it to work correctly. That's also an impossible question for anyone to answer before you tell them exactly which hammer, sear, and disconnector combination is in your gun. ...and even then, you may be looking at a few thousandths variation from gun to gun. I had obvious impact signs on the side of my firing pin with Titan/bolo/1pc sear combination. For most users that combination is 100% drop-in for the extended firing-pin block (FPB.) Edited April 7, 2017 by MemphisMechanic Link to comment Share on other sites More sharing options...
MemphisMechanic Posted April 7, 2017 Share Posted April 7, 2017 (edited) <oops> Edited April 7, 2017 by MemphisMechanic Link to comment Share on other sites More sharing options...
V2plus25 Posted April 7, 2017 Share Posted April 7, 2017 I bought the extreme fpb and actually had to file/polish machining marks on either side of the bottom of it where the trigger bar hits and raises it. Now it's nice and polished and works like a charm. Oh yeah and I also sanded down and polished the ridge a small bit where it blocks the firing pin. Link to comment Share on other sites More sharing options...
rootacres Posted April 8, 2017 Author Share Posted April 8, 2017 6 hours ago, MemphisMechanic said: 90% of the people out there don't make any adjustments to the block for it to work correctly. That's also an impossible question for anyone to answer before you tell them exactly which hammer, sear, and disconnector combination is in your gun. ...and even then, you may be looking at a few thousandths variation from gun to gun. I had obvious impact signs on the side of my firing pin with Titan/bolo/1pc sear combination. For most users that combination is 100% drop-in for the extended firing-pin block (FPB.) My bad, thats useful info for my question. I edited the post with the parts in my gun. Thanks Link to comment Share on other sites More sharing options...
MemphisMechanic Posted April 8, 2017 Share Posted April 8, 2017 (edited) I have the same setup you do, and had to do a fair bit of fitting. Most don't, but I did. I say a fair bit because I only removed a few thousandths but did so very slowly with lots of frequent checking to see if they contacted. Painting both parts with a sharpie then looking to see if that gets worn silver is helpful. Edited April 8, 2017 by MemphisMechanic Link to comment Share on other sites More sharing options...
C-Money Posted April 9, 2017 Share Posted April 9, 2017 Never seen a FP block tested at anything other than an IDPA match. Link to comment Share on other sites More sharing options...
V2plus25 Posted April 9, 2017 Share Posted April 9, 2017 3 hours ago, Twinkie said: Never seen a FP block tested at anything other than an IDPA match. Hell I'm surprised anyone at an IDPA match even knew anything about a Tanfo much less if the FPB was in there or not. Link to comment Share on other sites More sharing options...
MemphisMechanic Posted April 9, 2017 Share Posted April 9, 2017 10 hours ago, V2plus25 said: Hell I'm surprised anyone at an IDPA match even knew anything about a Tanfo much less if the FPB was in there or not. This would likely have been at a really big match. I've had guns weighed and slides stripped off and firing pin blocks checked, at exactly two really big IDPA matches. It's still uncommon over there, but it does happen. It doesn't require knowledge of a Tanfoglio. CZs are common enough and function the same, and anyone who knows even a little bit about guns is going to know what that button is for when they pull the slide off. Link to comment Share on other sites More sharing options...
rootacres Posted May 10, 2017 Author Share Posted May 10, 2017 Thanks for the help everyone. Does anyone have some pics of their tuned ext FPB? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now