springy27 Posted April 8, 2011 Share Posted April 8, 2011 hello i`m planning joining ipsc, i have a 1911 springfield trophy match and i reload my ammos, can you guys give me some idea like what division would be my gun at....and if i can use it i was planning of getting the cr speed deluxe range belt, cr speed mag pouches, double alpha race master 1911 holster, or i`m open for any suggestion, i been shooting my trophy match for awhile now and i shoot really good groups in it.... Link to comment Share on other sites More sharing options...
kalebg Posted April 8, 2011 Share Posted April 8, 2011 You should compete in Single Stack, check out the holster rules at USPSA.org...I dont think you can use a race holster in single stack. Link to comment Share on other sites More sharing options...
want2race Posted April 8, 2011 Share Posted April 8, 2011 Blade tech or Comp-tac holster would be the best route. I use a Comp-tac locking paddle on my CR speed belt. Yes on Single stack division. Link to comment Share on other sites More sharing options...
Erik S. Posted April 8, 2011 Share Posted April 8, 2011 +1 on single stack division since the Trophy Match has a bushing barrel. If you really want to use the race holster, buy some 10rnd mags and a magwell (even that's not really needed) and do Limited 10. Nice thing about having a bushing gun is it goes both ways! Link to comment Share on other sites More sharing options...
springy27 Posted April 9, 2011 Author Share Posted April 9, 2011 thanks guys... Link to comment Share on other sites More sharing options...
springy27 Posted April 9, 2011 Author Share Posted April 9, 2011 hello guys , what is the 10 rounds mags you use in Ipsc, here is the setup I`m thinking to get ....Cr speed deluxe range belt, Cr speed mag pouches and I`m not sure about the holster..can you help me with this guys please and thank you Link to comment Share on other sites More sharing options...
dapribek Posted April 9, 2011 Share Posted April 9, 2011 Chip McCormick or Wilson Combat 10 rounders are very good quality mags, hope this helps. Link to comment Share on other sites More sharing options...
caz41 Posted April 9, 2011 Share Posted April 9, 2011 My .02 is get a holster that is legal for Single Stack. You can still get the 10 round mag's and use the setup for Limited-10. Once you have shot a few matches in both divisions then make your decision about getting a race holster. The two holsters that want2race listed above will work in both SS and L10, but a race holster is L10 only. Link to comment Share on other sites More sharing options...
G-ManBart Posted April 9, 2011 Share Posted April 9, 2011 Are you really going to shoot IPSC (International), or are you going to shoot USPSA (USA)? The rules are different, and IPSC doesn't even have Single Stack. Link to comment Share on other sites More sharing options...
springy27 Posted April 10, 2011 Author Share Posted April 10, 2011 is cmc 10 round mags will fit in ipsc box , because the cmc powermag 10 rounder has a long slampad Link to comment Share on other sites More sharing options...
TonyT Posted July 19, 2011 Share Posted July 19, 2011 My SA Trrophy Match has been super reliable with 185 gr. LSWC , 185 & 230 gr plated, 185 & 230 gr. JHP and 230 gr. FMJ bullets. A very accurate gun which required changing the innards since the factory trigger was a mushy 5+ lbs. Link to comment Share on other sites More sharing options...
springy27 Posted July 22, 2011 Author Share Posted July 22, 2011 My SA Trrophy Match has been super reliable with 185 gr. LSWC , 185 & 230 gr plated, 185 & 230 gr. JHP and 230 gr. FMJ bullets. A very accurate gun which required changing the innards since the factory trigger was a mushy 5+ lbs. which part of the action did you change, like sears and hammer, hammer spring and what else, would you mind to specify every detail of it please. Link to comment Share on other sites More sharing options...
TonyT Posted July 22, 2011 Share Posted July 22, 2011 My SA Trrophy Match has been super reliable with 185 gr. LSWC , 185 & 230 gr plated, 185 & 230 gr. JHP and 230 gr. FMJ bullets. A very accurate gun which required changing the innards since the factory trigger was a mushy 5+ lbs. which part of the action did you change, like sears and hammer, hammer spring and what else, would you mind to specify every detail of it please. I replaced the hammer, sear, disconnector and hammer spring with a set from Frerking Gun Works. I have also used the Cylinder & Slide 3 1/2 lb. kits in other 1911's. A fellow shooter chose to have a trigger job done on the factory components. I opted to have the factory components available if I ever sell the gun. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now