Joedirt199
-
Posts
188 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Joedirt199
-
-
Gives more options for recoil spring weights as well
-
For all those recommending the armanovs, no one has made mention of the best swag ever. They send a key to unlock the shopping carts at places where you have to use a quarter in order unlock them. Think of all the money you will save on "renting" shopping carts without wasting quarters.
-
I did the same with my p07s and glock 19/23 rods. Just chuck the button in a drill and sand the outside till it clears the hole in the slide.
-
I like uspsa for concealed carry practice. More freedom in holster placement, more rounds fired and freedom of stage planning. There is a guy who regularly gets squadded with me who shoots AIWB with a cz and mags in pockets.
-
I just built and ran a cheap cmmg upper with parts I had on hand. Went with the 8.5" barrel and a taccom barrel extension for full 16" length. 30 round endo mags ran perfect and have seen too many people struggle with their homemade builds on dedicated lowers with stick and glock mags that are extended. Now just playing with buffer weight. Currently have standard AR buffer but have one of each weight up to try and see if the recoil is better. Holosun 510 green dot for optic.
-
Was trying to mill and mount a 1911 for RMR but not wanting to use the trijicon plate with rear night sight. Want to have a stand alone rear sight that is blacked out. I found a picture of what I am wanting done and asked the guys at Primary Machine if they could do it, my main go to guys for this kind of stuff. No go they said. Here is the pic
-
For production I just got a bunch of the metal bottomed 16 rd cz's and replaced the basepad with the rubber cz version. We shoot on big rocks and the rubber takes most of the beating. Also grippy when grabbing them.
-
Guess one of those grandma extended grabber things hanging off the back of the belt then?
-
On 9/29/2019 at 6:41 PM, Sokam101 said:
The flip and catch to save my back from bending over and picking up the round.
Supposed to bend at the knees.
-
You will be fine. Start low and work your way up. May need to mic a bunch and sort them into batches for .356 and .357. If the .357s dont shoot that well, get the lee bullet sizing die and squeeze them down to .356. What was the price you got them for?
-
Yup I load them to 1.1" or less. Very accurate in my p09 and shadow 1. Really liking win 244 powder as it is easy to find good combos at low powder charges.
-
A well informed eye could spot the different between the 2 bushings. Stock allows more of the barrel to stick out of the bushing. 10x is longer in front and meets the end of the barrel.
-
Yeah I had to clip some of the spring off and rebend it straight on the section that goes into the trigger spring retention hole. Hole was so small it didn't allow for the spring bends to go in. Lot of trial and error.
-
Might as well just go full kit. I have done the same to all my p series and if you do it by parts you will eventually get all the ones in the kit plus pay more for shipping. I switched back to the stock trigger return spring because the lightened one seemed slow to reset and sometimes I didn't let the trigger fully return to reset when shooting fast.
-
I would think the P09 and P10F would be very similar. Here are my best results with my P09.
.356 diameter
Penn 120 lead flat point & SNS 125 TC coated
WSF 4.0-4.2 grains
.355
RMR 125 matchburner
244 4.0-4.1
WSF 4.7
CFE Pistol 4.8
Sport Pistol 4.3
-
Yeah just need to eliminate the firing pin block on the non-shadow slide.
-
Yeah I grabbed a TS hammer for mine as it is the wider version for the shadows and the straight trigger with no hook at the bottom. Super short reset and nice break.
-
It's not that hard. I converted my sp01 shadow to sao for a short while. Realised it limited my options for divisions in uspsa so I switched it back. Already have a couple 9mm 1911s to use as single action options. Disassembly is the hardest part. Just a trigger swap and disconnector removal.
-
Damn that is deep
Que the "that's what she said"
Looks good.
-
Sent you a message.
Ask and ye shall recieve. Even has upgraded guts. Act fast pretty good price
-
Looking to order some biothane webbing and ratchet buckles to make my own shooting belts. Found some buckles that claim to be more of a flusher fit and not so thick so will see how those look.
-
My thoughts as well since people are using .356 from other manufactures with cleaner results.
-
Yup plate with the sight attached. They use ameriglo glock rear sights GL507 on the p07/p09/p10 builds and those angle away from the reddot.
-
Nobody said holoson 507 since it has the same foot print as the rmr. I have both and like the holoson a little better. The circle dot helps those that have trouble finding just a dot even though you can select just a dot, circle, or circle and dot reticle. Base is already sealed so no need for a sealing plate like on the rmr. The holoson doesn't seem as bloomy to me with a sharper dot and less edge distortion. Half the price of a trijicon so you may want to keep that as an option.
Armanov Spidergo grips
in CZ
Posted
Oh sure after I paid more for them on amazon. They did come with a nifty "key" for unlocking grocery carts that take quarters. Gonna save so much money now.