1911jerry

Thanks Guy Neill, I will FL size them.

I am starting to reload 300 black out. I was gifted a 3 die set of Redding dies. It appears to have 2 dies which deprime. One appreas to be a neck die, the other one is a full length sizing die. Does the neck die also size the cases, or just the neck area? Thanks

My wife would like a softer trigger on her carry pistol, Sig 365X. Maybe someone can direct me to a good established gun smith who might be able to work on it. I am in Phoenix, but can ship it out. Thanks

Thanks, will try it

Thank you

Is there someone local to Phoenix who has a shop and works on Glock triggers? Any help would be appreciated. Thanks

Thanks, will do.

Per 1K... plus tax

Are you using a neck sizing die after you resize, and before you use the mandrel die, or do you neck with a bushing during the fl sizing die? Thanks

I am thinking about getting an ultrasonic cleaner for my suppressors. Yea or Nay? Also which brand? Thanks

I was in a well known reloading shop today in Phoenix and saw primers (CCI benchrest) for $130 and CCI #41 for $120.

Do you all see a significant benefit to using an expander mandrel die vs FL with a bushing? I am about to start loading 6mm Dasher and was curious if this is an avenue to pursue for better accuracy. Plan on 600/Fclass type shooting. Thanks

Follow up question(s) please: I have had good success with no set back. I am reloading FGMM brass in 308, with 175 SMK projectiles. I have been using a neck bushing size .334. I am not sure if this is providing to much neck tension. I have bushings in 335, 336 and 337. Will to much neck tension cause grouping problems? What would be your recommendation.

I am looking to upgrade the trigger and sights on my stock M&P 22 full size. Any recommendations? I am in AZ and would like to keep it local. Thanks

I have a thousand or so 9mm with military crimps (Nato symbol). Do I need a special swaging arm, or can I use the 223 arm? Thanks

I use a Redding type S match die set, the full length resizing set. I use FGMM brass only with Sierra 175 grain SMK projectiles. The neck tension bushing is a 334 size, and the finished ammo comes out to 337. I seat 175 SMK's to 2.800. Case gauges 100%, goes into the chamber no issues. Would you think I need to do any type of crimp if I am running these loads in an AR-10 platform? This method holds the bullet really well. Thanks

I built my bench and just put the extra projectiles on the bottom shelf.

Thank you all.

What is the fb page called. I did a search, but only one page comes up for me. Thanks

I have had a JP low mass carrier in the polished stainless steel for awhile and would like to upgrade an AR. Currently I use a semi auto BCG with the red Sprinco spring and a Spikes ST-T2 buffer. Would you advise changing out the spring and buffer? Thanks

Thanks guys, I go to PT in the next week, I will bring up your suggestions.

Over the past 5 years, I have suffered from bones touching in the thumb joint. This caused a lot of pain. I recently had surgery where they removed some arthitis from the bone ends of my thumb joint, They did a tendon transfer from the wrist into the thumb joint. The good news is it removed the pain. After a few months of recovery, I can move the thumb pretty well, but have no strength in the right hand. Being a lofty "C" class shooter, I don't plan on burning down any area championships. I would like to start over after the other hand gets fixed. Any advice getting started again? After rehab, the physician says go at it until it hurts... I thought about shooting steel challenge with a 22, then production with a 9mm, then back to the 40. It might take awhile. Thanks JS

I believe it is threaded onto the u shaped part.

I posted this over at Nordic, but thought maybe someone else can assist. I have an older Nordic set for my 22. I want to take off the larger froegrip abd put a barrel nut on it so I put a different fore grip/rail I am trying to separate the threaded portion off of the u-shaped part. I have tried a strap wrench, no luck. Any advice? Can I just buy the u-shaped part from you? Thanks Jerry Snyder

Magpul 20 rounder off a bench, bagged