EddyB

Need some advice on what bullet weight to choose, trying to buy some subsonic 300 Blackout ammo from Atlanta Arms (I guess they have decent prices) but not sure which weight to choose "200GR subsonic FMJ" or "208GR subsonic A-MAX" It's going to be used out of a 8.5" inch Noveske barrel with either 7" or 9" suppressor, ammo is only for fun and target practice and to see how quiet it could get, both rounds advertise average 1000 FPS. Thanks in advance Sent from my iPhone using Tapatalk

I'm new to the suppressor world and seeking some advice........ I'm looking into getting a suppressor that works with both pistol and rifle calibers. So far I'm looking at the Liberty Mystic X I'm not sure if there is anything else better out there that covers that many calibers..... I'm looking to suppress the most common pistol and rifle calibers. Any advice or recommendations would be greatly appreciated Thanks in advance. Sent from my iPhone using Tapatalk

That's not a "short barreled Contender". ;-) This does the same thing (36 gr. bullet at just over 1000 fps) with off-the-shelf ammo. Although I usually run that barrel / can combo on a pistol. Hope my last posting gave a little more info :-) Sent from my iPhone using Tapatalk

Thank you all for the responses. As this is my first can, my goal is to be a little versatile, it's going to be used on multiple rifles and multiple calibers (not .22 rimfire). The last week I looked at many suppressors and one caught my eye, the "Rugged Surge 762" The ability to change the length from 9" to 7.5" and also change the end cap between 5.56 and 7.62 sounded very appealing to me also the mounting and locking system looked pretty good. It's kind of getting 2 Suppressors in 1 Also going to be using the Gemtech suppressed bolt carrier for reduced gas blowback So what do you all think about the "Rugged Surge 762" Any Positive or Negative comments are welcome :-) Sent from my iPhone using Tapatalk

I am building my first SBR (300 AAC) with an 8.5 barrel and of course will be putting a Can on it but there are many options out there and I'm trying to get some advice on which one to go with, most likely it will be the only one I get for a long while because of cost and process, a multi caliber would be nice for versatility ( l've been told to get 30 cal ), I would like to keep the cost around $800 but I am open minded :-) Any advise is appreciated. Thanks in advance. Sent from my iPhone using Tapatalk

What about powder coating, any body has an opinion Sent from my iPhone using Tapatalk

I was trying to find a red AR trigger online for my red AR theme build but I could not find one, so as an easy and cheap way, I'm thinking of painting the stock trigger, just the part that sticks out of the receiver to match all the red parts I installed. Any suggestions on what paint I should use, preferably something I can pick up at a local store. Thanks Sent from my iPhone using Tapatalk

Thank you all for the input, it really helped me a lot, I think I will build my own, this way I can get good quality parts over time without hurting my pocket and learn more about the platform in the process. Sent from my iPhone using Tapatalk

Looking for a good place online to get a quality at a good price AR-15 upper, currently looking at ar15depot.com but would like other suggestions / sources / recommendations to compare......... Thanks Sent from my iPhone using Tapatalk

I'm using lighter springs on my GLOCK and I'm getting few light strikes here and there, Any recommendations on which extended firing pin I should use ?? Thanks Sent from my iPhone using Tapatalk

Using titegroupe or/and CFESent from my iPhone using Tapatalk

Going to reload for Limited Major and trying to decide what would be the best bullet weight to use 180gr or 200gr. Any input is appreciated. Sent from my iPhone using Tapatalk

I'm using a SquareDeal B, currently loading 9mm and the cases most of the time are getting hung up or kind of stuck on the way down of the flaring die and its causing a small jerk that sometimes causes the primer to move out of place. I am thinking of using case lube. Any body knows if this is normal and is there a fix for it. Thanks Sent from my iPhone using Tapatalk

Compressed air in a can works great Sent from my iPhone using Tapatalk

I am loading 9mm on a square deal B, but the cases get kind of hung up on the way down from the flaring die Sent from my iPhone using Tapatalk

I'm new to reloading, I'm loading pistol cartridge and not sure what is the best case lube to use, I did some online research and it seams that Hornady one shot is the most common but I also red that sometimes cases get stuck in the resizing die when used.... What do you all recommend ???? Sent from my iPhone using Tapatalk

Whenever shooting a match I have have a good plan for the course of fire until the SO hits the button on the "Nuralizer" it goes .... Beeeep Sent from my iPhone using Tapatalk

Mag well and mag extension for limited Sent from my iPhone using Tapatalk

Glocks are one of few guns out there that you can count on them going BOOM wether the first time or 50,000 time Sent from my iPhone using Tapatalk

In my opinion KKM is one of the best Sent from my iPhone using Tapatalk

I say G35, it could be used in many divisions and you can load minor or major plus you can always get a 9mm conversion for it, Making it more versatile than others especially for competition use Sent from my iPhone using Tapatalk

I'm thinking of getting the SJC Heavy Weight Magwell for G35 for limited.... What do you all think ????? Any pros or cons are appreciated Sent from my iPhone using Tapatalk

Can I upload a profile pic through tapatlak Sent from my iPhone using Tapatalk

Comments and question box is too small so I wrote in it "see attached 60 pages" Sent from my iPhone using Tapatalk

The Game Sent from my iPhone using Tapatalk