3djedi

I use the stainless steel guide rod and 13lb spring. Sent from my SAMSUNG-SM-G935A using Tapatalk

Find what? Sent from my SAMSUNG-SM-G935A using Tapatalk

125g blue bullets Sent from my SAMSUNG-SM-G935A using Tapatalk

The CK comes with an extended firing pin. Problem is you can't load very long in the gun. Sent from my SAMSUNG-SM-G935A using Tapatalk

Interesting question as I have the same issue. My splits are always .22. Occasionally. 20..... best bill drill is around 1.85ish..... only because pretty fast draw to first shot. Probably just lucky indexing on the first shot. Sent from my SAMSUNG-SM-G935A using Tapatalk

Is this normal? My limited gun doesn't move at all. when the gun is assembled it seems really tight...... https://www.dropbox.com/sh/3vduvknjgqd82o5/AABWtwkxrdwlOysJPS9zGfNza?dl=0

You guys have any tips on where I should start with the AA7 with the 124g RN Blue bullet? Maybe like 8.5g? Sent from my SAMSUNG-SM-G935A using Tapatalk

Thanks! I went to the local store and found some AA#7. Bought a little to try. We'll see how it goes. Sent from my SAMSUNG-SM-G935A using Tapatalk

Ok thanks. From the burn chart I saw hs-6 is listed right next to autocomp with hs-6 being the faster. Didn't list CFE Pistol but I hear it's about the same as AC. AA#7 is slower than 3n38. 3n38 is really pricey though. I thought I heard Silhouette is a good one but I don't see it on the burn chart....... Sent from my SAMSUNG-SM-G935A using Tapatalk

So, worst case is probably light strikes then? Honestly, I'd rather switch powders than primers. I have a 1050 autodrive that is very sensitive to primers. Is HS6 a better powder? Sent from my SAMSUNG-SM-G935A using Tapatalk

Ok thanks! CFE Pistol is probably also not a great choice but I have around 16lbs sitting here I'd like to use up. Sent from my SAMSUNG-SM-G935A using Tapatalk

I ran 200 rounds through it today and it ran perfect. Shows just a little bit of cratering. Is that anything to worry about? I have tons of S&B primers and really want to use them. Thanks! Sent from my SAMSUNG-SM-G935A using Tapatalk

Small pistol Sent from my SAMSUNG-SM-G935A using Tapatalk

They are S&B primers. Sent from my SAMSUNG-SM-G935A using Tapatalk

Sent from my SAMSUNG-SM-G935A using Tapatalk

Since I'm new to open and not sure what's ok with 9mm major I thought I would ask if these primers look ok. I see cratering but is some of that ok in 9mm major loads? I think I will be using 6.4 to 6.5g of CFE for my load...... Sent from my SAMSUNG-SM-G935A using Tapatalk

Sent from my SAMSUNG-SM-G935A using Tapatalk

Sent from my SAMSUNG-SM-G935A using Tapatalk

Sent from my SAMSUNG-SM-G935A using Tapatalk

Closer ups....... 6.4g Sent from my SAMSUNG-SM-G935A using Tapatalk

Sent from my SAMSUNG-SM-G935A using Tapatalk

I think I will test some more around 6.4 or 6.5g... Seemed to run pretty good right there. Here's a picture of the brass. Does everything look ok? I don't have any experience with high pressure signs. I believe there is some "cratering" but how does it look to you guys?

Tested some loads today. Gun cycled and ran everything just fine. I noticed a bit of cratering at about 170PF. This is Blue bullets 125g RN @ 1.125" and CFE Pistol. Sent from my SAMSUNG-SM-G935A using Tapatalk

Lol just kidding Yes I have a chronograph. Sent from my SAMSUNG-SM-G935A using Tapatalk

What's a chrono? Sent from my SAMSUNG-SM-G935A using Tapatalk