IntenseImage

Not available just yet ... soon

Whats wrong with the factory ambi safety?

And FYI I tried a friend's DA choke wrench and it's too short on my long comp (using the original supplied adapter). Perhaps it's different w/o or on the short comp Sent from my SM-G975U using Tapatalk

I don't but Ive let others use the mag in their VR80s at matches. At this point the VR80s are well outnumbering the VEPRs [emoji41] Sent from my SM-G975U using Tapatalk

If you plan and shoot to it that CH never even comes into play. My 28 runs all day long and in multiple guns ... Talk to Tooth if yours doesnt Sent from my SM-G975U using Tapatalk

Thanks ...Cleaned it well and it basically ran since day 1 even using 1200s. 100rds of 1300s are my base recommendation. The Taccom buffer helps too Sent from my SM-G975U using Tapatalk

2 shooter, 1 VR80 I was 1st Open (of 21) and High Overall (of 70) Sent from my SM-G975U using Tapatalk

Elftmann and CMC were supposed to be working on them Sent from my SM-G975U using Tapatalk

Per Josh: Sorry for the delay. Been dealing with some health issues with my youngest son. Been meaning to send out an email to everyone who has pre-ordered with an update. So after talking with a few customers who ordered some of our other triggers we have found some slight variation in the distance between the hammer and trigger pins. This has caused a few guns to allow the hammer to miss the trigger dear upon reset. We had to cancel our EDM and redesign the geometry slightly to account for this difference. This has added some time to the process because of the change. I am supposed to have a new eta later this week. Sorry for any inconvenience. I am hoping to be back in the shop full time tomorrow and will get an email sent out to all the pre-order customers. Sent from my SM-G975U using Tapatalk

Dissident Sent from my SM-G975U using Tapatalk

RIA VR80

Just have em swap if you have tried some troubleshooting already Sent from my SM-G975U using Tapatalk

Bend some kydex and make a shield, use thermal wrap, modify some Mlok panels ...

Got u pumpkin Sent from my SM-G975U using Tapatalk

No but they said they would replace them if they don't work. Try loosening the clamp a bit, stuff it full, then snug it back down. It's just an alignment issue Sent from my SM-G975U using Tapatalk

It's a rough guess ....last match I believe it was an 18" circle @ 100 ... Held center and got bottom edge hit Sent from my SM-G975U using Tapatalk

6-8 low @ 100 Sent from my SM-G975U using Tapatalk

Coated lead ... Haven't grouped at 100, but have shot that far in matches Sent from my SM-G975U using Tapatalk

Jump to 8:40 ... It's about the grab Sent from my SM-G975U using Tapatalk

About here Sent from my SM-G975U using Tapatalk

I'd think w the weight and friction of a 12g stack you would want as much ass being the spring as possible. Sure the basepads I just added removed some of that spring pressure but I haven't run them yet to see how they are doing and if spring fatigue issues will show up sooner than without Sent from my SM-G975U using Tapatalk

Why would you do that Sent from my SM-G975U using Tapatalk

Cut it flush is fine and the easiest Sent from my SM-G975U using Tapatalk

Armanov.com ... I don't see why you couldn't but the mag holds 28 out of the box so would be 29 most likely Sent from my SM-G975U using Tapatalk

Yes, a modded factory 9rd holds 10 so I expected 11 but it took 12 and the factory 19 now holds 20 Sent from my SM-G975U using Tapatalk