-
Posts
117 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by RGC
-
-
Anyone using 356 diameters in 9 Major? Looking to standardize bullets w my 38SC.
-
I had some left over Autocomp....
Just kidding,....thanks on the OD.
-
6 minutes ago, BJB said:
You say 0.356", so that's the 125 HAP (The 115 gr HAP is 0.355"). 4.1 to 4.2 gr N320 @ 1.12" or so should put you around 130pf........shouldn't be a problem.
BTW: The Gen 5 Glock barrels aren't tighter, their throat however might be.
Thanks. Yes the 125 HAP. The Zeros are also 125 but their seating depth is different due to profile. But in general my concern or inquiry was related to the bullet OD.
-
I have a few thousand extra .356 Zero and HAP’s that I need to turn into something. Have plenty 38 SC so was looking to make some production friendly training rounds for a new to me Gen 5 Glock 34.
Read that these Gen 5 barrels may be tighter, etc. Anyone had any experiences or qualms with .356 in these barrel? I come from a world of “shouldn’t be a problem”....and then.
Looking for actual loads. I am going to fill with N320 with standard 130 pf load strength.
-
23 hours ago, Practicalomaha said:
Anyone have a Huncho open gun? I have one ordered and have talked to 4-5 different people that have them and overall have heard great things. But have also heard some bad things that they had to send it back to get fixed. Looking for more feedback from people who have them. Let me know your experiences. Thanks
What "bad things" were needed to be fixed? Manufacturing flaws I think would be rather rare...so was this a spring/trigger set up prob, etc?
-
Great recommendations....I ordered a Honcho and am intrigued by the engineering...AND, I ordered a 38SC (already have 20k brass and am set up for it), 9mm Major (agree with chasing brass comments and just want a flat comparison) and a 40 iron sight block (because I could...).
Will see in a few weeks I guess... -
Use both springs.
Clean extractor hook from any build up.
Clean extractor channel with Qtips.
Ensure no firing pin housing fitment issues as the extractor needs to move.
Chang springs every 120k
From my part checklist.
-
Going to set mine up over the weekend...if I have those issues, it'll be heading back and I will just stick to the pistol vibration devices.
-
Much appreciated.
-
Lots of great suggestions...I will look up Tommy Guns if local as well.
-
1 hour ago, Maximis228 said:
Mine will be here tomorrow.
Mine as well...
-
Ordered December 6. Once the tracking number was corrected verified its on the way and should receive shortly....
-
Got mine too....but they gave me the wrong tracking number.......so hope it shows up...
-
I would love to get my pre order in so that I can contribute to this post with actual experience vs speculation....
-
Yes, I know that. As stated in the OP I am looking to have foam cut for 2 pistols only and am looking for a trace of the Honcho from the factory pistol cut....
-
I have a Honcho incoming, and am looking to get a travel case made up for it an my other open pistol. Just need a pistol tracing psd with scale of the Honcho set up in 30SC and scope profile. Anyone have an outline of their foam insert of their factory case they would be willing to send to me? Pics don’t usually work....thanks.
-
On 11/17/2019 at 6:51 PM, avastcosmicarena said:
Anyone have any thoughts on the single sided safety vs the ambi safety? Does the ambi safety sit high enough on the right side that it doesn't get in the way of/dig into your hand with a high grip?
My exact problem, so ordered mine with the weak side shaved down to 1/8” wide....
-
Good to know. My mounts do not have a shield but was considering.
Very good info sir and appreciated.
-
Now to find one ,...
-
15 minutes ago, echotango said:
I have handled both and for a frame mounted open gun, I went with XL's. Very happy with my choice.
Thanks ET. It was where I was leaning to, especially as I have RTS2 mounts.
-
On 12/16/2019 at 4:49 PM, travisb2352 said:
Been really enjoying mine, dot is very crisp
I am torn between the two....Romeo 3XL or SRO....anyone run both and have any insights?
-
On 12/6/2019 at 6:29 PM, Aircooled6racer said:
Hello: I am thinking of selling my gray Pelican case once I find it since I never use it. Thanks, Eric
I would too if it’s a 1470...and I am just down the road....
-
Yes. 2 hole openings....I always pass (not to shun lefties).
-
Thanks...slapped a deposit down on a Race shop.......
.356 in 9 Major
in 9mm/38 Caliber
Posted
Thanks. I was thinking of running HAPs...and looking to get rid of 3500 .356 Zero 125's at the same time...but I may just dump them or reload some grinder weekend loads with them and move directly to the 115's for 9Major...