CZ85Combat
-
Posts
804 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by CZ85Combat
-
-
What is your trigger pull now? What do you want it to be?
-
Get the SP01 Shadow. it has a better trigger. Have the slide milled for the optic this will get the dot lower to the bore.
-
Call CZC and set it up. Ask them to mill as deep as they can. The multi optic cut will work with the old and new Deltapoint.
-
Win AC is a faster powder then 3N38
-
On 9/8/2017 at 0:36 AM, Akkid17 said:
whats the difference between the sp-01 shadow and the regular sp-01? I like the idea of the decocker version of the sp-01 but if it can't be milled as low its not worth the being able to drop the hammer without pulling the trigger.
SP01 decocker can not be milled as low. SP01 Shadow can be milled 0.250" deep.
-
6 hours ago, Kurusty said:
Does this make the weight?
Sent from my XT1650 using Tapatalk
Yes with room to spare
-
My Wilson Combat AR-9 14" barrel load is 2.5gn N310 with a 147 Blue bullet @ 1.150 130pf
-
CZ SP01 Shadow.
-
Ok so you only take one mag to chrono. You have no problem, you take the mag that passes the gauge. If you want all your mage to pass file the bottom of the base pad as it is about an 1/8" thick.
-
This weekend Local PA. 10 stage match, 259 round count and yes they do 10 stages every month and it cost a whole $25. Sundays start shooting at 9:00am done shooting and stage tear down finishing at about 2:30. 12 shooters on each squad. They have added Saturday this year with five 8 man squads. Saturday does set up, Sunday does tear down. Saturdays match sign up fills up in about 5min., and Sundays match sign up fills up in about 15-20min. 175 shooters shot this weekend. Shooters come from Virginia, Maryland, Delaware, Ohio, Western Pennsylvania, New York, New Jersey and Connecticut each month. I drive two hours each way for this match, others are driving four - six hours.
-
You could try CZ customs
-
All you have to do is polish the notch in the slide where the slide stop catches and slide stop and it will auto forward every time.
-
post a pic of the side of the mag.
-
Your powder charge is to low. Powder is not burning efficiently due to low pressure. you need to get your fps up to about 900 or more.
-
Do not get the drill out!
-
8 shooters in CO in today's match, last year two-three shooters in CO at each match.
-
56 minutes ago, WiII said:
I'm starting to get a little but hurt over this. The entire release of the Shadow 2 has been an FU to the US consumers. We had to wait a year longer and now the numbers are still insufficient to allow entry to production(which is the soul purpose of this gun).
Don't get but hurt, you can buy one if you want one, they are in stock all over. Just not enough buyers to push the numbers up. CZ is not going to ship guns in that are going to sit on shelves and take a long time to sell.
-
#1 For OAL you need to find out what your Shadow's barrel uses! What someone uses in their gun may or may not work in your gun. Do the push test. This link will help you out. Start at post #3
-
For the gun you are using Win 572 is not a good choice. Win 572 is a slow burning powder and with a 3.42" barrel a lot of powder will be burning out the end of your barrel. You can use a powder burn chart to get a rough idea of the powder that would work will with your gun. All powder burn rate charts are a little different so take it for what it is worth. On this chart you want to look for a powder in about #28-#38 +/- range.
-
That might not be a good idea, as not all optic's have a sealed bottom and the FP block spring may short them out. You need to leave about 0.010" above the FP block hole. A non FP block model can be milled 0.250" - 0.260"
-
Minor N320, E3, N310
Major N350, Auto-Comp, 3N37
-
19 hours ago, Bubing10 said:
Where did you send your slide to be milled? it looks like original from factory. clean job.
In 2013 CZC did the milling and installed the red dot.
-
This is my set up.
-
Wilson Combat AR9, 16" barrel. 2.5gn N310 147gn Blue Bullet @ 1.140 132pf. Soft and quiet, shoots like a 22.
Can I use 75B SA slide on an Accushadow frame?
in CZ
Posted
The 75B slide does not have the same con- tour as the slide on the Accushadow so by rule it is not allowed.