rinconjoe

I am trying to figure out wear everyone getting there powder data max i see on there web site as follows : 180 GR. HDY XTP Winchester WST .400" 1.125" 3.9 830 28,300 PSI 4.3 888 32,400 PSI

wow i was under the understanding max for WST was: 4.3 info below from there web sight 180 GR. HDY XTP Winchester WST .400" 1.125" 3.9 830 28,300 PSI 4.3 888 32,400 PSI

At rest primer slide adjustment: Set so that one primer, dropped down the tube, goes all the way into the Primer Seating Cup, 10 times in a row. if it don't what do I need to adjust it made it 8 times did the change : Angle of Primer Slide Operating Rod (13869) - Release rod from rollers and swivel it 180º so it's pointing straight up - it should be parallel with the Primer Housing Shield, or maybe outward "a little"; it should not be "inward" at all.

well this is what i ended up doing : Redding G-RX Carbide Base Sizing Die Kit 40 S&W, 357 Sig, 10mm Auto Redding G-RX Sizing Die High Density Polyethylene (HDPE) Bottle 32 oz Redding G-RX Sizing Die Bottle Adapter Lee Reloader Single Stage Press little slow but they all seem to pass after words case cage and all micrometers measures .

OK I not sure wear to start I start reloading and all sudden it don't put new primer in and next time does seems to be no pattern to why other than i seem to catch it when I have powder all over my system . makes it real hard to have pull shell out every time see if there's a primer sometimes goes along 20 to even stretches of possibly 50 then boom there goes again no primer old primer removed just not new primer. basically asking for help wear to start. sent email off to dillion seems there email department not that fast or strong .

why would you load past a COL 1.125

WST 4.0 GR 180gr Berry s double plated bullets col 1.125

a die that goes all the way down to size so we don't have to buy someone else dies to fix brass bulge

OKreloading with a dillion RL550B seems the ammo spent cases from my glock 23 I am going to need to take the bulge out , any cheap recommendations on how to do that wish there was way to do with my dillion:

yes to chronograph bought one today looking for a good target shooting powder for 40 S &W 180 FM J or even berry's 180 gr plated bullets shooting glock 23

Went to buy wsf all they had was wst wear do i find loading data for this powder thanks

OK this is wear to start my height is five foot eight , will be standing be dillion 550B eventually adding the strong mount I hope next month , so trying to figure out what height to make my bench , I am sure this can be a personal matter but give me somewhere to start , plan on 4x4 legs and mounting to wall , be 3/4 plywood . thanks thanks that great idea if i had my strong mount all ready any one have any ideas how long the aluminum roller handle is too the base strong mount Strong Mount. from standing to balded fist is 82 inch's does that help items I am planning on getting next month : Strong Mount Bullet Tray Aluminum Roller Handle Empty Case Bin and Bracket Quote: How to measure for any press (standing) Grab a tape measure. Stand in the location you are going to mount your press. Raise your press hand keeping your elbow at your side. (Like swearing in, in court.) Make a fist and put the end of the tape measure in your raised fisted hand and let it drop to the floor. Get another person to read the measurement to the floor. This measurement will be the highest the handle of your press should be mounted without fatigue. Grab your press. Measure from the top of the handle to the bottom of your strong mount. Subtract this from your original Hand to floor measurement. Now you have the custom bench height for your body. Note: If you have a case feeder, make sure your ceiling is high enough before building your bench. To make this work for a sitting bench. Important: Find a chair you will use for the rest of your life. If you change your chair height your measurements will change. Sit in the chair and follow the instructions while sitting. my height with fist is 82 inches thanks that great idea if i had my strong mount all ready any one have any ideas how long the aluminum roller handle is too the base strong mount Strong Mount. from standing to balded fist is 82 inch's does that help items I am planning on getting next month : Strong Mount Bullet Tray Aluminum Roller Handle Empty Case Bin and Bracket

wow good info especially for a new re loader like my self , i like 180 gr been shoot FMJ bullets , trying to stay away from lead with my glock , keep the recommendations coming my self thing buying in bulk better.

does anyone have any plans ? info on made reloading table , was thinking of building one so wondering about height with ect any starting idea's .thanks

well i am Joe from North Carolina Looking at getting into reloading my own ammo , I have friend who got rid of his RL550B , He sold it to me with just few items its still in box . he got something like a 1050 or something like that, so guess I need to buy all the other stuff . what I do have is this spear reloading manual , Lyman reloading manual , dillion 550B conversion kit , carbon dies pistol , scale beam type . , he said i could start with that but that there's a whole lot more stuff I could add and make it better .