frog1958 Posted November 9, 2023 Share Posted November 9, 2023 The bolt on my new 1301 comp pro doesn't lock back after firing the last round. When I cycle it manually with an empty gun .it locks back every time. The load was Winchester super target 2 3/4 ", 1150, 7 1/2. Any ideas? Maybe a heavier load? Beretta C/S forwarded my info to their gunsmith division, but after a week, o response. Link to comment Share on other sites More sharing options...
Alaskapopo Posted November 10, 2023 Share Posted November 10, 2023 19 hours ago, frog1958 said: The bolt on my new 1301 comp pro doesn't lock back after firing the last round. When I cycle it manually with an empty gun .it locks back every time. The load was Winchester super target 2 3/4 ", 1150, 7 1/2. Any ideas? Maybe a heavier load? Beretta C/S forwarded my info to their gunsmith division, but after a week, o response. That is a light load and is not running the bolt back far enough to lock open. Try hotter ammo Link to comment Share on other sites More sharing options...
Nolan Posted November 10, 2023 Share Posted November 10, 2023 Walmart super target with the steel case or super target with the brass case? 1145fps 1-1/8oz should be hot enough to fully cycle the 1301. How new, how many rounds fired? Temperature? Lube? Gas system, piston and exterior of magazine tube absolutely NO lube. As Alaskapopo posted try some other ammo, the cheap Winchester stuff is somewhat inconsistent, the brass cased ammo is much more consistent. If the gun is brand new try several boxes of 1200 or 1250 1-1/8oz ammo and re-try the lighter ammo. If no go, measure the wire diameter of the gas valve spring on the barrel. If the wire diameter is smaller than 3.3mm, there are two fixes. Replace the spring with the heavier spring from the 1301 Tac, p/n C95447 or install the A400 gas valve spacer p/n C5g164. The weaker spring lets too much gas through the gas valve and the gun won't cycle light ammo. https://www.practical-shotgun.com/543 https://www.practical-shotgun.com/beretta-blink-spring-update Unfortunately changing the spring or installing the spacer are a pain in the butt requiring a special valve spring compression tool and spanner wrench. Here's my post about the spring compressor I hacked together. https://forums.brianenos.com/topic/270212-gas-valve-spring-compressor-for-1301/?do=findComment&comment=3172957 Nolan Link to comment Share on other sites More sharing options...
frog1958 Posted November 10, 2023 Author Share Posted November 10, 2023 Thanks Alaskapopo and Nolan. Gun is new and it was the first time fired (25 rnd) on a cold day (mid 30's). I know about not lubing the gas sys. I'll try some fed 1200 fps 71/2 and some 1200fps slugs. Link to comment Share on other sites More sharing options...
Nolan Posted November 11, 2023 Share Posted November 11, 2023 Shot weight is somewhat more important than velocity. 1 oz slug or birdshot will probably need to be over 1300fps in the cold if the gun is not well broken in and lubed. Nolan Link to comment Share on other sites More sharing options...
frog1958 Posted November 16, 2023 Author Share Posted November 16, 2023 Ran some Remington 1 1/8 , 1200 fps, 7 1/2 today without a hitch. Thanks for the responses. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now