factorysponsered Posted November 30, 2013 Share Posted November 30, 2013 Let's see if I can describe this without taking pictures. The lifter gets stuck below the bolt release, I have to depress the the bolt release to free the lifter. Make sense? What can I do to fix this problem? Link to comment Share on other sites More sharing options...
hysupra Posted November 30, 2013 Share Posted November 30, 2013 Pull the trigger group out, the pins fit pretty loosely so something might have moved around. Also clean it up a bit while you have it out. Heres a link on how the trigger group goes together. http://www.shotgunworld.com/bbs/viewtopic.php?f=58&t=219571 Link to comment Share on other sites More sharing options...
rrickysee Posted December 1, 2013 Share Posted December 1, 2013 I have had my 930JM do the same thing. If i push the bolt release really hard (i think it travels to far and won't let the lifter come back down, then the bolt gets hung up on the lifter). It has only happened to me when releasing the bolt, not while shooting. I have thought about making the bolt release shorter, so this can't happen. Link to comment Share on other sites More sharing options...
factorysponsered Posted December 1, 2013 Author Share Posted December 1, 2013 I have had my 930JM do the same thing. If i push the bolt release really hard (i think it travels to far and won't let the lifter come back down, then the bolt gets hung up on the lifter). It has only happened to me when releasing the bolt, not while shooting. I have thought about making the bolt release shorter, so this can't happen.I have the opposite problem. The lifter gets caught on a hook from the bolt release. Causing me not to be able to load rounds into the tube without holding the bolt release Link to comment Share on other sites More sharing options...
hysupra Posted December 1, 2013 Share Posted December 1, 2013 Have you taken the release apart before? The spring might be sideways holding the release open. PM me if you need detailed on how to get the latch out. Does it function normally other then this issue? Is the lifter centered in the magwell? Link to comment Share on other sites More sharing options...
wgj3 Posted December 1, 2013 Share Posted December 1, 2013 (edited) Not sure how much you've been playing with the trigger group, but if you read onto the 2nd page of the link posted above, you will come to a post regarding the exact orientation on the tubes with retaining clips that go into the trigger assembly and the pins that hold the assembly in the receiver. As best I can make out, the clips should be on the "bolt release" side of the trigger group, and the end of the pins with the extra grooves should be on the same side to be retained by those clips. Edited December 1, 2013 by wgj3 Link to comment Share on other sites More sharing options...
factorysponsered Posted December 1, 2013 Author Share Posted December 1, 2013 Have you taken the release apart before? The spring might be sideways holding the release open. PM me if you need detailed on how to get the latch out. Does it function normally other then this issue? Is the lifter centered in the magwell?I have not done that before. I'll pm you. It functions, but loading it is a pita Link to comment Share on other sites More sharing options...
factorysponsered Posted December 1, 2013 Author Share Posted December 1, 2013 Not sure how much you've been playing with the trigger group, but if you read onto the 2nd page of the link posted above, you will come to a post regarding the exact orientation on the tubes with retaining clips that go into the trigger assembly and the pins that hold the assembly in the receiver. As best I can make out, the clips should be on the "bolt release" side of the trigger group, and the end of the pins with the extra grooves should be on the same side to be retained by those clips. Everything is where its supposed to be. Pins, clips, etc Link to comment Share on other sites More sharing options...
moss930 Posted June 24, 2017 Share Posted June 24, 2017 Has anyone found a solution to this? I recently had the same issue with mine after one season of use. If anyone has some help that would be great! It is a real pain and I'd like to fix it before duck and goose season... Link to comment Share on other sites More sharing options...
timawa Posted July 8, 2017 Share Posted July 8, 2017 Dremel the lifter about 1-2mm shorter? Or polished the side of the lifter closer to the bolt release. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now