skorittnig Posted October 7, 2010 Share Posted October 7, 2010 HI all, I have read every thread (to my knowledge) about chamfering- and decided to purchase a 45 degree set in order to very lightly chamfer the cylinder holes on a 625. I purchased the corresponding brass pilots as well- and when I went to insert the pilot into the cylinder hole tonight it fit, however- it won't allow the chamfer bit to get close enough to the cylinder to remove any metal. Am I doing something wrong? This gun has is moon clip ready, I didn't know if the cylinder had been shortened enough to make the pilot non-functional? Thanks, shay Link to comment Share on other sites More sharing options...
Carmoney Posted October 7, 2010 Share Posted October 7, 2010 Very common scenario. Typically means your chambers are too tight, which is an epidemic problem on 625-2s and 625-8s. You'll need to ream the chambers to correct SAAMI spec, then your chamfering reamer will work just fine. Link to comment Share on other sites More sharing options...
Carmoney Posted October 7, 2010 Share Posted October 7, 2010 I would add there is no reason to chamfer "lightly." The guns that utilize moonclips benefit from a fairly heavy chamfer. (Remove the extractor first, though, so you don't adversely alter the timing.) Link to comment Share on other sites More sharing options...
skorittnig Posted October 7, 2010 Author Share Posted October 7, 2010 (edited) just to clarify Mike- the brass pilot goes in all the way (flush with the other end). My problem is that it won't quite make it far enough to let the chamfer bit touch the cylinder mouth. Should the end of the brass pilot be sticking out (protruding) past the end of the cylinder? I just want to make sure I am using the pilot correctly I guess. Thanks Edited October 7, 2010 by skorittnig Link to comment Share on other sites More sharing options...
Carmoney Posted October 7, 2010 Share Posted October 7, 2010 If the chamfer cutter won't hit the chamber edge, things are too tight in there. Again, you probably need the chambers reamed. Lemme guess, it's a 625-8, right? Link to comment Share on other sites More sharing options...
cas Posted October 8, 2010 Share Posted October 8, 2010 (edited) I think it's "pilot error". I say that because I've seen it with a couple pilots (from Brownells) on a few cylinders of various size and vintage. I know Brownells sells two types (or did anyway) for the newer and older guns IIRC but it didn't seem to matter, neither worked unless turned down. Edited October 8, 2010 by cas Link to comment Share on other sites More sharing options...
Toolguy Posted October 8, 2010 Share Posted October 8, 2010 Sounds like those pilots were made for 45 Long Colt, not thinking about revos being 45 ACP. Link to comment Share on other sites More sharing options...
Carmoney Posted October 8, 2010 Share Posted October 8, 2010 I'm tellin' ya.....I see it all the time on the dang tight-chambered cylinders from 625-8s! The pilot on the chamfering reamer won't fit in there until the chambers themselves have been reamed. Next question......? Link to comment Share on other sites More sharing options...
skorittnig Posted October 9, 2010 Author Share Posted October 9, 2010 (edited) I'm tellin' ya.....I see it all the time on the dang tight-chambered cylinders from 625-8s! The pilot on the chamfering reamer won't fit in there until the chambers themselves have been reamed. Next question......? I received my .38/.357 pilot today and it pushes all the way through (on my 686). I think Mike is spot on with his reaming suggestion. Edited October 10, 2010 by skorittnig Link to comment Share on other sites More sharing options...
cas Posted October 9, 2010 Share Posted October 9, 2010 I'm tellin' ya.....I see it all the time on the dang tight-chambered cylinders from 625-8s! That explains the -8's. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now