yekcoh

what I'm getting is that I'm not the one breaking the law but he sure is. I guess it's a question of morality..? So I pulled the plug for now.

I looked online but I could not find a concrete answer. I sold high cap 2011 mags in classified. Buyer disclosed his shipping address and it's NY. Are there any consequences to shipping my mags? If this question is unfit for the forum section, please take down. Thank you

Interim solution for now is switching to 3n38 which seems to be working so far; 200 no issue. Will test several hundred to confirm...

I should have uploaded pictures from the get go. https://imgur.com/a/Rp1Bnet I am using the same load that I used for MPA which works flawlessly. You can see with this gun, the chamber area gets whatever you call (cornmeal or unburnt powder) resulting the next round to not fully chamber. So Id have to “assist” the slide to close

So I did the push test and the bullets are guaged with a hundo it measures 3.780 at the edge(neck) so I dont know what else I could do to test for proper crimp. Any idea?

Thats not the topic of discussion. Im not asking about making pf. Im asking about a potential solution to the malfunction I am experiencing with the particular powder I am using

The gun is a middy length (5” with thread) with 4 barrel holes. If we measure barrel length to the first hole, itd be almost 4” Does that make this gun a shorty then? Low pressure and too short of barrel length to burn the powder but the gun tracks wonderful. And it makes either ipsc or uspsa power factor easily. Id do Anything to make this gun work!

My load recipe clocks in at 167pf at 9.4gr. Ive been practicing with it because Its feels great despite the jams. Dot tracks great. Its loaded for ipsc nats but Im afraid I wont be able to trust it.

If it's a primer issue, it would be an easy fix but even cci srp caused problems albeit less..

It chronos slightly higher. barrel hole position is almost the same but this one is kkm which is known for higher muzzle velocity

I got a new gun built recently. 2011 with 5" KKM with TI comp and 4 holes into the barrel chambered in 9. barrel is pvd black. The usual load that I am used to with my existing open guns is 9.4gr of AA7. This gun for some reason seems to be leaving a lot of unburnt powder in the gun. Sometimes it gets so bad that the chamber gets build ups of unburnt powder causing the next round to jam. Builder said it's his first time hearing such a thing. Funny thing is when I first got the gun, it ran flawlessly for the first 500ish rounds then I started experiencing this problem. So I checked my ammo: 1.172" federal spp mag (cci srp seems to burn better). Ammo appears to be sized and crimped correctly. Any tips or suggestions are appreciated.

I have let the moderators know in the past but the response I received was rude and dismissive. In summary, a member referred me to a seller he could vouch. The seller sent me clearly fake pictures to deceive me. The evidence was rock solid but the mod refused to take any actions or investigate the member who referred because he said the seller wasnt the member himself.

So this is my third time running into a scammer with fake post it notes photoshopped into the picture. I'm pretty convinced this one is fake. https://www.dropbox.com/scl/fo/xt0jtchlgjilhuuuonk9w/h?rlkey=4rcmrhu87atdue159g5tu8my4&dl=0

Picked up a DS9 O, wondering if anyone is using alpha x holster. If so, which insert block fits best? I don't want to pay for the flex

Got mine back from stonebridge gunworks.

Ahhh. It’s not like it improves reloading speed or shooting.. it’s like removing the front sight but I understand

I understand that dehorning in USPSA for CO or production is allowed as many have done Is dehorning like the following picture deemed illegal in IPSC? Or could this be deemed as minor detailing and removing sharp edges

Looks great. Whats your load recipe? I was told the side holes dont impact the velocity. Im very impressed with the hole spacing of the mpa

you got pics? you got pics? And please don't count comp ports as holes

Thats 9 major

I'm starting to see guys with a barrel hole cut into the comp and the muzzle thread. I know SVI has been cutting holes half way into the comp but now I see guns with an entire hole drilled into the comp before the first comp port starts. I guess the benefit could be that the holes drilled are far away from the chamber making it easier to achieve power factor. but then that's not how pressure works and things start to behave strangely with slow powders we use. what are the thoughts on the first barrel hole drilled into the comp and the muzzle thread? My initial take was that this could hurt the integrity of the comp or the barrel as it drilled into both but SVI has been doing it for a long time so it must be reliable.

I acquired a CZ S2 regular, not OR. CZC offers options for a direct mill and for their proprietary plate mill. Has anyone done direct mill for SRO? They mill as far down as possible and actually cut clearance for where the glass sits. I asked for a picture of the cut slide without an optic installed but they don't have any. Anybody got a pic of it without the optic. I'm curious what it looks like. Also, do they do anything to cover up the bare steel or is it left as machined?

Ti comped hybrid barrel open gun

hahahahahahahahaha!!!

I'm based in Nevada. I am looking for a custom 2011 builder who could build one in a relatively short period of time. I am also looking for someone to fit a new barrel on an existing gun I own. Mod please kindly let me know if I'm in the wrong channel.