Miggz55

Just got the Zulu stock and installed the Armaspec Stealth SRS buffer. With the secondary spring installed, the guide rod pokes out about 1/2” past the detent. I can get the rifle to close, but then the guide rod ends up a bit in the bolt carrier and I can’t open the receiver after. Any thoughts? Anyone have the same setup or a JP setup with the Zulu? Sent from my iPhone using Tapatalk

Nice! Thanks for sharing. Sent from my iPhone using Tapatalk

Great feedback. Any pics of the XLR? I prefer a shorter length of pull also, so I’m hoping the modularity of the Zulu will fit well.... Sent from my iPhone using Tapatalk

And it holds only 12 2 3/4 rounds? And pics of how far it sticks out? Sent from my iPhone using Tapatalk

Shorten your OAL? Sent from my iPhone using Tapatalk

Anybody actually have a +7 of +8 from MOA on a Stoeger?? Sent from my iPhone using Tapatalk

M3K - Nordic Compnents +2 Bought it for New Jersey compliance which limits to 6 in a Semi Shotgun Sent from my iPhone using Tapatalk

Right now I have a +2 that gives me +3 with 2 3/4 shells... why wouldn’t a +7 give me at least 8? Sent from my iPhone using Tapatalk

Haha, will take the tube down and reassemble as needed.... Sent from my iPhone using Tapatalk

Does anyone know what size MOA Precision tube the M3k needs to achieve 12+1 when using 2 3/4 shells? Do I need an +8 extension? Or will +7 get me there? Sent from my iPhone using Tapatalk

Just ordered a Zulu from Optics planet for ~$125 Sent from my iPhone using Tapatalk

Yea, I had the Luth and it wasn’t my favorite... plus, its a bit on the heavy side! Sent from my iPhone using Tapatalk

Been looking to swap my stock on my 3-gun rifle.... I have been really considering the Odin Works Zulu 2.0, but figured I’d ask the experts what their go to is... any suggestions? Also, any thoughts on Armaspec Stealth recoil springs? Do they compare to JP SCS? Sent from my iPhone using Tapatalk

For those that are loading 75gr and 77gr, any good deals to be had right now? Sent from my iPhone using Tapatalk

Great suggestion! Thanks... Sent from my iPhone using Tapatalk

I’m the same way. Although I’m using a Hornady LnL press, I picked up the Frankford Arsenal case prep station with seems to be a one stop shop for prep work. The only downside is the ream vs swage debate. Wondering if I should add a swage tool rather than ream the primer pockets... Sent from my iPhone using Tapatalk

Same, as I would think Is true for most... Sent from my iPhone using Tapatalk

Thank you! I’m off to order some 75gr pills. What COAL? Sent from my iPhone using Tapatalk

Thanks for the reply guys... for those that are reloading hoser and long range, any recipes you’d suggest? I have an 18in Balistic Advantage 223 wylde fluted Barrel. I started loading with CFE 223 at 25gr with Berry’s 55gr bullets. Have set up a ladder test at 25, 25.3 and 25.6 but have yet to chrono them. Sent from my iPhone using Tapatalk

I just delved into reloading 223, and man is the case prep a PITA... wondering if the professional shooters out there prefer to load their own 223, or buy factory Ammo instead? Maybe a balance of both is best? I.e. bulk 223 for short range targets and precise hand loads for distance targets? Looking for advice as to where I should invest my time and money. I do enjoy reloading as a hobby, but at current market prices, there is not a ton of cost savings. Sent from my iPhone using Tapatalk

Turned out there was some residual powder in the primer slide not allowing it to seat properly. Once I tore it down and cleaned it thoroughly, everything was back to 100%. Sent from my iPhone using Tapatalk

I just pulled 200 9mm rounds that I loaded as 1 in 10 may have had some moisture in the cases (found out the hard way). Anyway, I made a mess of my press, but cleaned it up good. When I went to start loading again, the primer seater no longer lines up properly with the press. Anybody know how to realign it? I can’t be the only one! Sent from my iPhone using Tapatalk

I haven’t replaced mine yet for my Glock 34, but after adding the magwell, the stock base pads hide inside the well... if one was stuck, I wouldn’t be able to remove it easily. And they have become tougher to seat as mentioned above. Hard to justify $200 in base pads, but I may swallow my pride soon. Sent from my iPhone using Tapatalk

Tightened up the crimp and that seemed to get the job done. Thanks for the advice! Sent from my iPhone using Tapatalk

Thanks. Will give that a shot! After posting, I looked at the recently loaded cases and I may need a slightly tighter crimp. Using .356 pills... Sent from my iPhone using Tapatalk