Qoo

Thanks again, yes I am using Chrono. What's the recommendation charge to start with? I am not lazy >< just try to learn from the beginning. Thanks If I were you I'd figure out what OAL will spin consistently free of your rifling (as you can see you're getting ~0.010" variation from your bullets/process), then load six rounds each at 7.0gr, 7.4gr, 7.8gr, and 8.2gr, chrono and draw a curve; within the useful range of the powder you can predictably extrapolate data in a, more or less, linear fashion. I would also give 115s a try, I personally prefer them to 124s. Thanks for the tips, will follow this instruction to see if i can get the gun runs smoothly or not.

really appreciate your help. I will lower the powder charge and shorter the OAL and see what happen first.

Thanks again, yes I am using Chrono. What's the recommendation charge to start with? I am not lazy >< just try to learn from the beginning. Thanks

Thanks very much for your feedback. I have contacted Bobby and he said for the gun I have with 124 gr MG bullet the COAL should not exceed 1.150" So, I guess I will have to readjust me sizing die to shorter the OAL and try it. The concern I have now is I am using 8.0gr of HS6 powder, so shorten the OAL to 1.150" would it be safe? Anything I should be look out for? Sorry for my newbie questions. Thanks

I appreciate your help. I have the CK Arms Thunder 9mm Blackout Open Gun After each round fired, the slide will not fully back to battery I will definitely need to recheck my sizing die to make sure proper placement should i get the cartridge gauge to further verify that i have the right amount of crimp? I am currently using MBX magazines with grams spring and follower

Thanks for your helping here. Definitely the rounds are not spin freely in the chamber, and some of them are not even sit flush, i believe those are too long and the tip of the bullet is touching the rifling. The feeding issue i am having now is fire the first round and the slide will not fully back to battery, i should of take some pictures yesterday while i was shooting to show the exact problem. I am currently using the MBX magazines and i have changed to the Grams spring and follower, the original follower seems printed out of the 3D printer and i keep having problem with the original follower, some rounds will drop into the mag tube.

I have loaded some rounds and looks like my OAL is too long and have some feeding issues, my seating die might not yet fully adjusted, i am getting variants on my loads. I have some 1.160", 1.165", 1.168", 1.170" I have asked Bobby and he said the bullets i am using (Montana Gold 124gr JHP) should not exceed 1.150" coal, i am at 8.0gr of HS6. Any suggestions?

i still have about 2K of the CCI for my Glock 34 and after i use up the CCI i will switch to Federal, so lighter springs should be fine with the Federal primers.

I just saw his post with the new design of the hammer spring, maybe i should get a hold with him to see if he can sell me one to try or not...lol

I am ordering the light hammer spring and light firing pin spring from patriot defense now. Hopefully that will help a bit on the DA pull, still need to take my gun to a local smith for polishing job. Thanks again!

Thanks much for your prompt reply, there is another recoil spring in a plastic bag, the bag is not sealed, i will try to swap with the current one and see which one is lighter. I got it used

Hello All, What are the weights of the recoil spring and hammer spring in the stock 3 xtreme? I am thinking to buy some springs and play around with, but i need to find out the current weights of the recoil spring and hammer spring in my stock 3 xtreme. Thanks

Welcome from Michigan

http://gregcotellc.com/cart/eaa-witness-sar-k2-b6p-mecgar-c-134/eaa-witness-tanfogliolarge-frame-17-round-9mm-mgwit9lfafc-p-1089.html 17 rds if legal in your state

Hennings huh~~ i guess i finally decided to go with Hennings. Thanks very much for all the help

I am debating for the Hennings or Shock Bottle. They both looks similar.

I totally agree with you, my stock 3 xtreme comes with 4 and i just bought another two mags, so i was hoping to get two more of those same base pad, but the price is ridiculous!!!

Thanks very much for the tips, i really appreciated.

Copy that, many thanks~

OK. How about recoil spring? maybe Titan Hammer as well? the current one is Delta Hammer.

Do i need to change the hammer spring and recoil spring from the gun?Just gauge the trigger pull - DA - 8lb 7.2oz SA - 3lb 10.7oz Beside the polish all the contact points, what springs should i change? I am using Federal Pistol Primers. Thanks Polish the plunger strut bar, the wedge and the inside of the wedge. Also polish the hammer strut bar. Put a CGW fp spring on the plunger, or a BIC pen spring on the plunger. Thanks, will have to spend time on the polish work now.

Do i need to change the hammer spring and recoil spring from the gun? Just gauge the trigger pull - DA - 8lb 7.2oz SA - 3lb 10.7oz Beside the polish all the contact points, what springs should i change? I am using Federal Pistol Primers. Thanks

Does anyone know where i can purchase the EGD Xtreme Large Frame Base Pad? I can't find a US distributor selling these base pad except Eric's online shop and a few European online shops. Thanks

Welcome from Michigan

Thanks for the feedback, i am totally agree with you, once the pistol arrive will need lots of polish job to get it up to par, wish my hand could hold the stock 2 or lim pro tight then i don't have to spend the extra dollars for the xtreme version.