eboadway
-
Posts
315 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by eboadway
-
-
School is open! Start reading! Lots of invaluable lessons to be had here.
-
I'm perfectly happy with mine. Screwed it in with Locktite, hasn't loosened up.
-
Henning has frame and upper videos at:
http://www.henningshootsguns.com/tech/tech.tanfoglio.main.html
These are for a Limited model but will get you started.
The Atlas thread in the CZ forum is a wealth of solid information too!
-
TechNetArmory has one on GunBroker for $1099.99. There are 2 others on there as well.
-
I Would try removing a very small amount of material from the rear of the sear leg until the trigger bar has enough room to pop up and engage the sear leg. You can reproduce this process with the slide off by cock in the hammer and pressing the trigger bar down if it does not come all the way back up it will cause you the problem we discussed.
That did the trick, thanks!
-
I run every round through the hundo. The few that don't pass go in the practice box. Takes only a minute!
-
CGW Joe Tool
in CZ
I love having new tools, but this one made me say "Huh?".
-
Please join me in Vermont. I can't imagine waiting 4 months for a gun, not being able to shoot target arrays at the range, etc.
-
Sorry, 1 piece.
-
My SA and DA function after fitting the T3 disco, but the SA won't drop the hammer after being reset by racking the slide. File the top of the wing a bit? Thanks.
-
P09 vs SP01
in CZ
I sure wish they had made the P-09 to take the same mags as the SP-01, I would love to get a P-09 as back-up to my SP-01 (or vice-versa). If they used the same mags that would be perfect.
Eric
Truth. I took an SP-01 mag to the LGS to confirm what others' had said. If it had fit I would have bought the P09 on the spot.
-
Well the 75b IS a fine handgun...
-
I'd like to trade thin, black aluminum grips (taken off when new) for CZ rubber grips. Any takers? Or I could offer $. Thanks!
Ed
Hell I'll make that trade
It's a great deal and I'd be happy to see Mr. Atlas take advantage. PM'ing you sir.
-
I'd like to trade thin, black aluminum grips (taken off when new) for CZ rubber grips. Any takers? Or I could offer $. Thanks!
Ed
-
Any word on interest for the holster? Thanks.
-
That's the video is learned on, but put your frame in a vice for the swap. Frees up a hand!
-
I also decap then wet pin clean. But I'm uptight and enjoy the extra step(s) once I see that sparkly brass!
-
Would a couple of coats of spray paint be too ghetto?
-
Do you have a large frame Stock II? If so, the Springers will not fit. I have them for my CZ and they are great. First thing I tried was putting them on my Stock II mags which (of course) was a disappointing failure. I bought the Shockbottles and really like them. The finish matches the frame really well.
-
Right now I am shooting .40 Minor with my Stock 2. I am shooting Extreme 165 gr's seated at 1.135 with 4.0 grains of Titegroup. I was using BBI's with the same powder load, same weight but they ended feeling a little too soft in the gun.
Before when I ran 180's they were alright but super slow and felt very sluggish in the gun. The 165's from Extremes just are better for my gun in my opinion.
WJM
I'll have to try that load. Right now I'm using 180g Extreme's at 1.14 with 3.4 grains of Titegroup. Plenty accurate, but a bit sluggish as you mentioned...
-
3.1 grains of TG
147 extreme rn
1.145
Federal primers.
132 pf
The gun doesn't move at all.
I use this as well. Very soft shooting with minimal recoil, although TG is a pretty dirty powder.
-
I use the new toolhead stand.
-
The primer bits should have been included with the original purchase. Did the first owner not have them?
-
Thanks for the add!
WTB Stock II factory front sight
in Tanfoglio (EAA / IFG)
Posted
Sure, let me know if Mr. Atlas doesn't have a few dozen!