[Screwdrivers for Modern Smith & Wesson side plates]

https://www.amazon.com/dp/B003F6FKBA?psc=1&ref=ppx_yo2ov_dt_b_product_details

[38 Super or Super comp brass?]

I would stick with Super, I carry a Dan Wesson Guardian in 38 Super and I can buy self defense ammo at my local gun shop (well I could)

[Revolver? Die on the vine?]

If you get bored, try a fixed time classifier

[Revolver? Die on the vine?]

Thanks for all this, I love it

[I had a dream]

Can it have a 38 Super cylinder too???

[Lost the set screw on my rear sight.]

My local ACE has a few drawers that are even marked "Gun Screws"

[New member & heard this is the place for competition shooters]

Welcome from another 1911Addict member

[327/627 and the .38 Super]

I have a 627 in 38 Super and TK  Smith & Wesson 929 9mm OEM Moon Clips STD B/S, work perfectly with almost all brands of brass.

 

I have a totes full of brass and don't even sort it, sometimes I get a round that is too loose and I just toss into a box to shoot out of my 1911s

[Exporting data from LabRadar?]

IS there an easy way to change the weight of the bullet? Using the phone app

Friday I tested 14 loads and 2 of them were different weights then the rest, I ended up leaving the unit on 200gr and did the math for the 230s when I got home

[Exporting data from LabRadar?]

I do not think there is a way to Arm the unit from your phones app.

I going to play with mine in a minute and Ill check it out, whats frustrating for me is changing the weight of the bullet.

I went to the range Friday and tested some 200gr bullets vs 230gr and I would like the app to ask me what grain bullet im using.

 

All I do is type in the FPS into a spreadsheet I made and it calculates the PF for me

[LabRadar measuring a PCC with compensator...]

I put the comp 4 to 6 inches downrange of the unit

[627 trigger pin repair.]

https://americasgunsmithshop.com/

 

Is another great place to deal with

[627 trigger pin repair.]

This happened to my buddies 929 and it took like 6 months when he sent it to S&W.

By the time they even looked at it, months had passed and then they realized it was a Performance Center gun so they had to send it to that department and the wait started all over again.

[What to do to a 929]

Are you going to reload for it?

[The Blue Bullet .38/.357 160g Round Nose]

I reload them in Short Colt and 38 Super for my 3, 627s

[Which powder drop do I need?]

Yes I am using Redding micro dies, Thanks for the advice

[Which powder drop do I need?]

Reloading for my S&W 627 in 38 Super, .358 blue bullet, 160 gr. Dillon 650. I have tried the 38 Super/9mm powder drop/flare and 38 Special. 

Both of them lead to me shaving a bit of coating off the bullet when seating, no matter how much flare I have.

 

I have read about Mr. Bullet Feeder and Uniquetek

 

Any recommendations?

 

Thank you,

[S&W revo bolt sticking]

Where is the spring on the wishbone for the lock? Are you sure the wishbone isnt moving forward a bit and allowing the lock to contact the hammer? Or allowing the lock to engage? 

[Madison, WI matches?]

We also have a great time in Polo IL

https://practiscore.com/tcgc-polo-march-2024-special-classifier/register

[Madison, WI matches?]

https://winnequahgunclub.org/

 

[Help optimizing SW trigger action? Comparing TK Custom, Apex Tactical and RevUp hammer set ups for SW revolvers?]

I have been installing, Apex, TK Diamond and even carving up stock hammers in N frames and all are around 5LB trigger pulls with Wilson Combat springs. Of course we all use federal primers

[Help optimizing SW trigger action? Comparing TK Custom, Apex Tactical and RevUp hammer set ups for SW revolvers?]

Do you reload?

[We are now taking pre-orders for RevUp Action(TM) hammers]

Are you ever going to have them in stock again for N frames?

[38 Short Colt 160gr]

[Revolver red dot]

I am going to try a 510 I took off my pcc.