[929 brass and moons combo]

12 hours ago, ysrracer said:

 

Buy .035 moon clips?

 

I have never seen .035 for a .45acp

[929 brass and moons combo]

3 hours ago, testosterone said:

Yes.

I have 3, one of them will close but will not turn with .040 clips as well. 

I have the tool to fix it but cant be bothered and honestly dont fully appreciate what other problem it might make, so that gun just runs .035's.

What is involved to fix that problem? I have a 625-2 .45acp that I just bought for ICORE.

I cannot close the cylinder with TK Moon clips .40.

But they work fine in my 625-JM

Calling TK soon, IDK if he will need the whole gun or just the cylinder

[Screwdrivers for Modern Smith & Wesson side plates]

https://www.amazon.com/dp/B003F6FKBA?psc=1&ref=ppx_yo2ov_dt_b_product_details

[38 Super or Super comp brass?]

I would stick with Super, I carry a Dan Wesson Guardian in 38 Super and I can buy self defense ammo at my local gun shop (well I could)

[Revolver? Die on the vine?]

If you get bored, try a fixed time classifier

[Revolver? Die on the vine?]

Thanks for all this, I love it

[I had a dream]

Can it have a 38 Super cylinder too???

[Lost the set screw on my rear sight.]

My local ACE has a few drawers that are even marked "Gun Screws"

[New member & heard this is the place for competition shooters]

Welcome from another 1911Addict member

[327/627 and the .38 Super]

I have a 627 in 38 Super and TK  Smith & Wesson 929 9mm OEM Moon Clips STD B/S, work perfectly with almost all brands of brass.

 

I have a totes full of brass and don't even sort it, sometimes I get a round that is too loose and I just toss into a box to shoot out of my 1911s

[Exporting data from LabRadar?]

IS there an easy way to change the weight of the bullet? Using the phone app

Friday I tested 14 loads and 2 of them were different weights then the rest, I ended up leaving the unit on 200gr and did the math for the 230s when I got home

[Exporting data from LabRadar?]

I do not think there is a way to Arm the unit from your phones app.

I going to play with mine in a minute and Ill check it out, whats frustrating for me is changing the weight of the bullet.

I went to the range Friday and tested some 200gr bullets vs 230gr and I would like the app to ask me what grain bullet im using.

 

All I do is type in the FPS into a spreadsheet I made and it calculates the PF for me

[LabRadar measuring a PCC with compensator...]

I put the comp 4 to 6 inches downrange of the unit

[627 trigger pin repair.]

https://americasgunsmithshop.com/

 

Is another great place to deal with

[627 trigger pin repair.]

This happened to my buddies 929 and it took like 6 months when he sent it to S&W.

By the time they even looked at it, months had passed and then they realized it was a Performance Center gun so they had to send it to that department and the wait started all over again.

[What to do to a 929]

Are you going to reload for it?

[The Blue Bullet .38/.357 160g Round Nose]

I reload them in Short Colt and 38 Super for my 3, 627s

[Which powder drop do I need?]

Yes I am using Redding micro dies, Thanks for the advice

[Which powder drop do I need?]

Reloading for my S&W 627 in 38 Super, .358 blue bullet, 160 gr. Dillon 650. I have tried the 38 Super/9mm powder drop/flare and 38 Special. 

Both of them lead to me shaving a bit of coating off the bullet when seating, no matter how much flare I have.

 

I have read about Mr. Bullet Feeder and Uniquetek

 

Any recommendations?

 

Thank you,

[S&W revo bolt sticking]

Where is the spring on the wishbone for the lock? Are you sure the wishbone isnt moving forward a bit and allowing the lock to contact the hammer? Or allowing the lock to engage? 

[Madison, WI matches?]

We also have a great time in Polo IL

https://practiscore.com/tcgc-polo-march-2024-special-classifier/register

[Madison, WI matches?]

https://winnequahgunclub.org/

 

[Help optimizing SW trigger action? Comparing TK Custom, Apex Tactical and RevUp hammer set ups for SW revolvers?]

I have been installing, Apex, TK Diamond and even carving up stock hammers in N frames and all are around 5LB trigger pulls with Wilson Combat springs. Of course we all use federal primers

[Help optimizing SW trigger action? Comparing TK Custom, Apex Tactical and RevUp hammer set ups for SW revolvers?]

Do you reload?

[We are now taking pre-orders for RevUp Action(TM) hammers]

Are you ever going to have them in stock again for N frames?