mspiredm3

Looks like when I'm ready to get a bit more serious, I need to move into USPSA. I have other guns I can use in IDPA such as a Walther PPQ if need be or can always pick up another CZ that meets the criteria of what I want to shoot

Nope, ten round .40 mags have a short body and a big plastic block for a base pad, whereas ten round 9mm mags have a full length tube with a dimple which can in fact be drilled out. However you're in luck, Exile Machine sells full cap mags to shooters in restricted states disassembled into parts kits and they recently got a shipment of TS .40 mags. Thanks for the referral to that site! Anyone know the length on these? I'm guessing well over 141mm and closer to 170mm? https://www.exilemachine.net/shop/magazine-cz-75-85-9mm-25rd-2238.html

I think for now, I am going to get a CR Speed setup that can be used for both guns. In the event I want to run IDPA, I can use the Phantom in the Kydex holster I already have. From there I can get whatever else I need for whatever else I want to get into at the time. Just wanted to make sure that the CR Speed holster would fit both the Phantom and Tac Sport, and it seems it would.

I should have mentioned the Tac Sport is in 9mm. The ribs that go down the length of the mag are there for both the 10 round version and 20 round version. I imagine they use the same magazine for the 9mm and 40, but put in those ribs for the 9mm to take up soem "slack" or space that would normally be there when using the 9mm instead of the 40...

A modified Phantom and a modified Tac Sport would fall into Limited? I really want to start using the Tac Sport ASAP due to it's higher mag capacity, weight, mag well, etc. What other holster's are out there for the Tac Sport that would meet the IDPA rules?

The competition I will be doing, for now, is very lax and doesn't have many rules. However, in the future, I will probably be stepping it up to IDPA or something of the sorts, in which my Phantom wouldn't make production due to the race hammer. I think it would be running in custom or modified? Don't know if the CR Speed is ok in those divisions, but if not, I can just use my regular Kydex holster if I have to...

Isn't the CR Speed WSM holster some what adjustable? From what it seems, one holster fits many different platforms? Or am I getting the wrong idea from their website?

So this past Saturday I had my first taste of competitive shooting and I am HOOKED! So, I have some questions... I just got a Kydex holster and mag pouch for my Phantom, which is the setup I was running. However, I want to get a setup for my Tac Sport in order to run that as well. BUTTTT, I want to get a rig setup that is as universal as possible, without any lack of performance due to that fact. I mainly want to be able to run my Phantom, Tac Sport, and possible a 2011 down the line. Suggestions for a holster, mag holders and a belt that fits above criteria? Also, for my Tac Sport, I currently only have 3 10rd mags. From looking at them and pictures of the 20rd mags, it appears the only thing stopping the 10 rounders from being standard capacity is a stamped dimple that prevents the follower from going down any further. Can these dimples simply be drilled out in order to allow the mags to load to full capacity? Anyone ever try this? Here is a link with pics of the 10rd mags for reference of the dimples. http://czcustom.com/czts9mm10rdmagazineca.aspx Thanks!

Ok, I know what you mean now. The original is a solid pin. I did buy the Phantom used, but the pevious owner didn't say he changed anything but the hammer spring out. I'm sure David will replace it, I will get a replacement when I place my next order with him for the SRS kit and a few other goodies

Not sure what a coiled spring pin is, but the original is very similar to the Cajun pin

I have a 13# in my Phantom and have not had one single ignition issue in thousands of rounds. Are you positive the spring is not lighter than 13#?

A 10mm is on my want list, sometime down the road. If they make this, it will be at the top of that list!

I have the Cajun trigger pin in and after I read this I went to change the pin back to the original. Found the true issue, the Cajun pin broke in half. The original and Cajun appear to be the same diameter.

So while the pin is in the gun, put a larger punch on one side to hold the pin in place, then use a smaller punch and hammer it hard to attempt to spread the ends of the pin? How would you get the pin out later if need be?

Hey guys, This issue seems to be getting worse... After a few hundred rounds, the trigger pin seems to walk out just enough to not let you use the gun in DA. It will still pull fine in SA. If I push the pin back into place, everything is fine again. Any solutions? Slightly larger trigger pin available?

That Silver Gun Kote is freakin AMAZING!

Contacted Davids as I love his products, but he doesn't have the wider hammer for the Tac Sports

This one? Out of stock too http://shop.cz-usa.com/P-19506/Competition-Hammer-Sa-Only.aspx

Based on my experiences, I totally agree with this! But a crisp and light trigger make it even better!

The trigger started out pretty crappy and was over 3#! It has gotten much better (it's not around 1.8#), but still I feel it needs some work. I had fired a TS 40 before buying mine, and I remember the trigger being much nicer... The break just isn't as clean as I would expect it to be. My Phantom with CGW hammer and other mods breaks much nicer. Oh, and I already have the CZC magwell too. I've never played with recoil springs in any of my pistols. What are the benefits? Yea, it's a 9mm. I want the race hammer, but it's been out of stock for months! I have an extra 13# hammer spring, I think I will throw it in and see how it feels

Haha! Exactly the two options I was thinking about

As is my habit with anything, I must mod it! Already got some flat aluminum grips and a SS guide rod...So, some questions for you guys... 1) What is the benefit of a reduced power main/hammer spring since the gun is SA only? 2) I already got a a flat SA only trigger from CZC. Are there any DIY's on how to install it? 3) I believe I have seen an aluminum guide rod plug, where would I find one of those? 4) What else can I do to it? Thanks guys!

Yes, it's a 9mm. I think I figured out what is happening. At times, while loading, I have felt that more than 10 rounds are able to fit (I will start counting from now on). I think when this happens, the follower is allowed to pass the dimples. However, this doesn't mean I can load the entire mag. Either the the round above the follower is catching the dimples or something else is limiting it to somewhere around 11-12 rounds. So, when the follower goes below the dimples that it's not supposed to, when coming back up it can catch one of the dimples, which causes it to jam up. Make sense? I don't have my mags marked, so I don't know if this is only happening with one mag. Will mark them for next time.

Been having this issue since day one. While shooting, the gun will stop feeding due the magazine getting jammed up. What appears to be happening is the follower is tilting to one side and catching a dimple that is on either side of the mag. This dimple, I believe is only on the 10rd mags as it's the dimple that limits it to 10rd. Anyone else experience this or know a fix? Thanks in advance.

All reloads. Are there any other slide stops that fit the Phantom, maybe one that is a big thicker. Wouldn't hurt if it was extended too...