-
Posts
2,098 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by norbs007
-
-
Dawson recommends a special loctite product for their front sights, don't remember the number, but it is green, and they sell little tubes of it for reasonably cheap. That is what I used on the Dawson front sight on my Stock II, and I haven't though about it since the day I installed it about a year ago...
Good info, I will use Green if ever the Red loosen up. Thanks!
-
Some people get good results sanding down the wood grips and either applying silicon carbide or skateboard tape.
-
-
Love the magwell too...
-
-
I start out "preparing" as soon as the last shooter is finished, and everyone is
down range taping / setting steel.
That gives me about a minute to myself, reviewing the COF, and how I'm
going to handle it ( shoot it and reload), remove jacket if necessary, make
sure my mags are loaded and in their proper pouches, my hat is on or
backwards depending on the COF, my earmuffs are in the ready position.
At "Make Ready" , I've already reviewed the COF and I'm now ready to
make sure I have :
1.a. put my muffs on my ears.
1. turned my red dot to the correct brightness
2. load the correct mag & make sure my other mags are in the right spot
3. check a round chambered,
4. slowly and deliberately holster - make sure it doesn't fall on the ground, and I leave the holster lock off
5. review what I'm going to shoot first
6. confirm with the RO any questions about the COF - tell him which way I'm going to run
7. NOD.
^^This^^
Step to the line, load, holster, call on Jobu , nod for the beep and start blasting.
-
Are these considered full custom pistols? What makes these $4000 guns? I've heard the name Limcat but have never seen one. I think KC Eubosio shoots them, correct?
Wow, there's actually one available to buy right away... you normally have to wait for a while to have one built.
-
What fishsticks said... ask me how I knew
-
I have almost all... Safariland, CR Speed, DAA and even Ernie Hill. My pants size is 38 and size 42 for all of them works perfect for me.
-
I used BBI 147gr on both my S2 and Lim Pro @ 1.100" without issues. But won't be surprised if you find inconsistency between the barrel chambers, my two S2s got different barrel length
-
Anybody selling the roll pin for the ambi-safety lever? Since they get damaged or lost easily I would like to stock up some.
-
Once proven solid I will switch all to an RTS.
-
-
Beyond my comprehension that a specific model in its original configuration is on the APPROVED list and yet not allowed if you cannot close the box. I like the wider ambi-safety on the Limited Pro and shouldn't have to modify it.
-
Why can't it be like IPSC
-
-
-
Hmmm, I just slapped an Aimpoint T1 on mine, hope it doesn't break it.
-
I love mine, went through the same experience but shot way more shells the day before the match. Polished the internals that night and it ran 100% at the match. I tried the Briley extended choke but it won't screw all the way down, the Carlson extended Win choke worked better.
-
I am running a blade tech with boss hanger and thumb screws and it has been the best thing since sliced bread. I have no problem with unwanted movement and the holster is not too tight. Hope you get it fixed
Same here, mine was perfect. Blade-Tech will make it right.
-
-
-
I usually run 10.2-10.4 sith an almost identical gun and get 173-175 PF easily, if you're not compressing loads you can keep going up .1 till you find that "sweet spot" as mentioned earlier, once there, you will definitely know it!
Boom!
My sweet spot is at 10.1gr @1.235 on a 650. MG 124gr JHP and WSR primers and average 170pf all day long, highest it went was 173pf in hot weather.
-
Henning new magwell coming loose ?
in Tanfoglio (EAA / IFG)
Posted
Was it not tight during initial install? I have to rubber mallet mine in place, did not use loctite on the screw and it's all marred from reload practice sessions... did not move out of place at all. But good idea using loctite on screw, will do that too.