-
Posts
645 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Will_M
-
-
Where can I find squadding info or at least what time slot I signed up for?
-
I'd say extractor issue. Replace spring with M2.This past weekend I had two failures to eject. One with a 1550fps 1oz Xtreme slug and one with a 1300fps 1 1/8oz 3.25 dram STS Nitro.
Both times the empty shell was still in line with the bore but with the bolt to the rear and a new shell on the lifter. Reaching in and pulling the empty shell out allowed the bolt to close and chamber the fresh round.
What would cause a failure to eject like this?
I plan to do this anyway, but the shell extracted fine, just didn't eject. What makes you think it's the extractor?
-
This past weekend I had two failures to eject. One with a 1550fps 1oz Xtreme slug and one with a 1300fps 1 1/8oz 3.25 dram STS Nitro.
Both times the empty shell was still in line with the bore but with the bolt to the rear and a new shell on the lifter. Reaching in and pulling the empty shell out allowed the bolt to close and chamber the fresh round.
What would cause a failure to eject like this?
-
I took the pin out to clean under the shell catch at a major match once and promptly lost the little hairpin clip that retains the pin. As an emergency measure, I used the tip of a flat-blade screwdriver across the hole and gave it a tap with the hammer to peen a little notch on both sides of the opening. I figured on replacing the clip when I got back, but a year and a half later it is still just retained by the screwdriver notches haha. Like the plumber's leaky faucet, my shotguns are always the last to get worked on
This is perfect, thanks.
-
Are you referring to part number 42 on this page?
-
What's the best way to keep the shell catch pin from walking out? Taking it apart a few too many times is allowing it to walk out under recoil. Would peening it with a center punch work?
-
I've seen some guys shoot from this position by hanging the magazine off the lip of the ramp and pulling the magwell into the ramp with their support hand.
What's the advantage to this way vs resting the handguard on the lip or using the magazine as a monopod? I wish I had some pictures to explain what I'm describing.
-
What parts should we be looking out for as far as wear goes?
-
I'm using the SilencerCo Specwar brakes on my rifles. I like them so much that I don't ever use my can on my 3 gun rifle, but the brake stays on anyway.
It's an awesome brake that just so happens to be able to mount a can.
-
Has the NRA World Championship in WV replaced the Trijicon World Championship in Kentucky? They seem like identical format.
-
Bring your rain gear. It's gonna be a long, wet day.
-
Freedom Gunworks built with 9mm and .40 uppers. One gun gives me the perfect package for USPSA, 3gun, steel, and a fantastic suppressor host.
This is absolutely my new favorite gun and runs like a top right out of the box.
-
The further you drive to the match and the higher the entry fee, the more likely it is your turrets will get turned.
-
Not a whole lot of people signed up so far. Is this still going to happen?
-
Prize table is at the match hotel.
-
What's the procedure if we are unable to stay for the prize table?
-
Looks like it's going to be a rainy weekend.
-
Will-M.. 24 inch barrel, LM carlson choke, barrel clamp, and truball low velocity slugs . 50yrds=1 1/2 right, 100yrds 5 inch right. A flinch starts up when shooting slugs
Maybe I'm flinching. Shooting 1600FPS 1oz slugs off a bench sucks.
I'm going to try the low recoil again this weekend. Maybe I SHOULD try a barrel clamp and see if it pulls it back in the right direction?
-
Always shoot slugs before you cut up your shotgun!
Duly noted.
-
No barrel clamp.Barrel clamp? That is usually the culprit if it is that far off on windage.
And selling it would suck because not many people want a cut up shotgun and I could end up with the same problem.
I was shooting off a bench and someone said that might affect POI?
-
Everybody knows he spray tans.
-
Yep. 24" barrel. So is it common for people to have to do large windage hold overs? Full size IPSC targets are one thing but small plates would screw me.
-
My slugs consistently shoot 8-9" right at 50m. Is this common? LM Carlson Choke, mix of Xtreme and Truball slugs.
-
Does anyone have any more ideas on how I can get the Versamax to quad-load easier? The lifter is pressing so hard against the first shell going into the gun that it keeps it from going into the mag tube. Two grown men were unable to get the shell to even move after it wedges itself like that.
Loading one at a time it works smoothly.
2015 Benelli Generation III Gun Championship Presented By MGM Targets
in Multi-Gun, Rifle & Shotgun Match Announcements
Posted
Any answer to this?