missed it by that much Posted April 21, 2017 Share Posted April 21, 2017 OK, I have a question for you guys that have much more knowledge then I do. Since I got my 929 back from the factory having had the crane detent ball installed as it was missing. I've been playing with loads. What I've noticed is that it's trying very hard to shoot great. I'm getting one or two fliers consistently with most bullet/powder combinations. I am shooting off bags at 50 ft and can generally shoot one inch or less with my 38 super and 357/38 special revolvers at 25 yds and sometimes 50 yds off the bench. My question is I have a cylinder reamer which I have used with the other revolvers. Can I use a reamer on the titanium cylinder? People have talked about honing the cylinder. How is this process different than reaming? Bullets I have tried are 115&125 zeros, 124/135 acme, 135 bayou's both. 356 &.358, 147 extreme, 160 b&b .356. The powders I've played with so far are vv320, titegroup, aa#7. As that's what I have on hand. Here's some pic's of the last targets from last night. Most groups hovering around 1.5 and 2.5 inches. I could call it good but like to tax as much accuracy as I can. Any suggestions would be appreciated. The black square is one inch the outside square is two. Oh and using Winchester brass.These are all 8 shot groups Sent from my SAMSUNG-SM-G900A using Tapatalk Link to comment Share on other sites More sharing options...
alecmc Posted April 21, 2017 Share Posted April 21, 2017 i'd be more concerned with - all cylinders timing up correctly. forcing cone crown Link to comment Share on other sites More sharing options...
Toolguy Posted April 21, 2017 Share Posted April 21, 2017 (edited) +1. Looks like some chambers may be off a little. Usually you will get tighter groups as you go over 1100 fps with the lighter bullet weights,125 and under. Do not try to ream the chambers. You will trash the reamer due to the coating on the titanium. BTDT. Honing is using an abrasive like a flex hone. Edited April 21, 2017 by Toolguy Link to comment Share on other sites More sharing options...
missed it by that much Posted April 22, 2017 Author Share Posted April 22, 2017 Ok thanks guys I checked timing and crown both looked good. I did try the 115 zero Conicals. Maybe I'll play with those more. Could take it to Joe at mo Joe and have him check it out. Thanks for the reamer clarificationSent from my SAMSUNG-SM-G900A using Tapatalk Link to comment Share on other sites More sharing options...
Taroman Posted April 22, 2017 Share Posted April 22, 2017 number your cylinder's charge holes to identify the culprit(s) Link to comment Share on other sites More sharing options...
missed it by that much Posted April 22, 2017 Author Share Posted April 22, 2017 That's a good idea will doSent from my SAMSUNG-SM-G900A using Tapatalk Link to comment Share on other sites More sharing options...
Ignatz Posted April 22, 2017 Share Posted April 22, 2017 My 929 shoots the same way. A one hole group of 5, with 3 on the outer edge. At 25 yards its under 2"s, so its good to go. On mine, I feel the throats in the cylinder are not perfect, causing the problem. Mine originally was shooting 4" groups at 25 yards with the same bullet pattern. 5 close and 3 fliers. A crown cut and forcing cone cut brought the group size down dramatically, but still has the 5 in tight and 3 just outside. But with a total group size under 2" at 25 yards, I'm happy. Link to comment Share on other sites More sharing options...
missed it by that much Posted April 22, 2017 Author Share Posted April 22, 2017 Yea going to have it crowned, honed, and forcing cone cleaned cut. Then I'll reshoot. Can't hurt right?Sent from my SAMSUNG-SM-G900A using Tapatalk Link to comment Share on other sites More sharing options...
Toolguy Posted April 22, 2017 Share Posted April 22, 2017 Can't hurt, might help. I do that to any new to me gun. Then I know it will shoot as well as it's going to. I have seen crowns and forcing cones all over the map from the factory. The worse they start out, the more good it does to recut. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now