RickyH Posted June 19, 2016 Share Posted June 19, 2016 Installing a short reset and disconnecter in my 's 75 p-01 and the double action works for the single action does not. Any help please Link to comment Share on other sites More sharing options...
eerw Posted June 19, 2016 Share Posted June 19, 2016 Need so material removed fro vertical face that contacts trigger bar, to allow the trigger bar move forward a little more. Link to comment Share on other sites More sharing options...
RickyH Posted June 19, 2016 Author Share Posted June 19, 2016 (edited) Thanks! That why this is the first one I've worked on. I put the other disconnect in that automatic accuracy did a trigger job on and it works. That's just a lot of putting it in and out to see when I finally get it right. Thanks for your help Edited June 19, 2016 by RickyH Link to comment Share on other sites More sharing options...
RickyH Posted June 19, 2016 Author Share Posted June 19, 2016 So I need to remove some metal try it and repeat until I get it to work? Link to comment Share on other sites More sharing options...
bowenbuilt Posted June 19, 2016 Share Posted June 19, 2016 (edited) You are correct and it only takes a very small amount of metal to make a big difference. i use a black magic marker on the vertical face of the disco so i can see where i am removing metal and to make sure i take off an equal amount across the face of the disco. I just realized yours is a de-cocker. That is a lot of work. Edited June 19, 2016 by bowenbuilt Link to comment Share on other sites More sharing options...
RickyH Posted June 19, 2016 Author Share Posted June 19, 2016 Can you used grease on the lifter spring because that little spring is hard to get to stay with the lifter? Link to comment Share on other sites More sharing options...
RickyH Posted June 20, 2016 Author Share Posted June 20, 2016 I'm using a stock Hammer can I buy one from Cajun and it work without removing any material from the disco? Link to comment Share on other sites More sharing options...
bowenbuilt Posted June 21, 2016 Share Posted June 21, 2016 (edited) Maybe but not 100% because there is some difference in the geometry between the 2 hammers. Would also depend on how close you have the disco to zero pre-travel. Edited June 21, 2016 by bowenbuilt Link to comment Share on other sites More sharing options...
RickyH Posted June 21, 2016 Author Share Posted June 21, 2016 I have no adjustment screw or nothing like that Link to comment Share on other sites More sharing options...
RickyH Posted June 21, 2016 Author Share Posted June 21, 2016 The SA works if you pull the hammer back but it does not work if you cycle the slide Link to comment Share on other sites More sharing options...
bowenbuilt Posted June 21, 2016 Share Posted June 21, 2016 After you cock the hammer how much trigger pre travel do you have before the trigger goes solid? Link to comment Share on other sites More sharing options...
RickyH Posted June 22, 2016 Author Share Posted June 22, 2016 Zero pre-travel Link to comment Share on other sites More sharing options...
ryback Posted June 22, 2016 Share Posted June 22, 2016 Hello Guys, I installed the pre b disco but I can not engage the pistol. I pull the trigger totally (no screw in the trigger) but the hammer can not down because the sear does not ries up enough high. I tried with the original and the competition hammer too. Do you have any idea why is not work? Thanks Ryback Link to comment Share on other sites More sharing options...
ArrDave Posted June 22, 2016 Share Posted June 22, 2016 Hello Guys, I installed the pre b disco but I can not engage the pistol. I pull the trigger totally (no screw in the trigger) but the hammer can not down because the sear does not ries up enough high. I tried with the original and the competition hammer too. Do you have any idea why is not work? Thanks Ryback Which gun is this in? I hope a non FPB model. The Pre-B discos only work in the non FPB models. If you have a block you need more swing forward. Link to comment Share on other sites More sharing options...
ryback Posted June 23, 2016 Share Posted June 23, 2016 Hello Guys, I installed the pre b disco but I can not engage the pistol. I pull the trigger totally (no screw in the trigger) but the hammer can not down because the sear does not ries up enough high. I tried with the original and the competition hammer too. Do you have any idea why is not work? Thanks Ryback Which gun is this in? I hope a non FPB model. The Pre-B discos only work in the non FPB models. If you have a block you need more swing forward. CZUB SP-01 Shadow Link to comment Share on other sites More sharing options...
bowenbuilt Posted June 23, 2016 Share Posted June 23, 2016 Zero pre-travel Keep fitting the disco. You have a little more metal to remove yet. Link to comment Share on other sites More sharing options...
bowenbuilt Posted June 24, 2016 Share Posted June 24, 2016 Hello Guys, I installed the pre b disco but I can not engage the pistol. I pull the trigger totally (no screw in the trigger) but the hammer can not down because the sear does not ries up enough high. I tried with the original and the competition hammer too. Do you have any idea why is not work? Thanks Ryback You are going to have to fit the new disco. Call Stuart or Zack at CZ Custom or David at Cajun Gun Works and they will walk you through in a jiffy. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now