zfields

I paid 450 for my utility.

Nordic stopped making them last I heard. As for the clamp, I plan on ordering the briley one. The Briley is WAY oversized compared to other tubes I have used on other guns. The nordic clamps I had would not work.

Briley doesn't have anything listed for CZ. I have there tube on my 712 right now, and I know they were listing it only for beretta at the time. I'm going to post the two designs I have finished sometime later tomorrow. One looks a lot better, but will cost more. The other should come out considerably less expensive. I'm waiting to hear back from a guy, but it won't be until the 6th at the latest.

Still working on the handle....I think I found the shop to do it Sent from my Incredible 2 using Tapatalk 2

Awe cmon, shotgun is the best part Happen to seen a big bucket of A2's for cheap I think that may get this price point down into doable territory.

the only problem is you go from 5.95mm, to 4.5mm, then back up to whatever handle size you want to do.

That's funny, I was talking to a buddy of mine, and we were bouncing around just putting a 1/2x28 thread on it, and you can stick an AR muzzle device of your choice on it.

That paddle saddly is a complete no go. My quotes at 30+ units were 90 EACH just for production.

Got a couple quotes, still not to the point where I can offer it at a price that would be fair. The extra slots are what is killing it, but I'm worried about the extra weight effecting reliability.

Well if you have any machinist buddies, let me know.

Looks good,..sorta like that guy's in post #38... http://www.brianenos.com/forums/index.php?showtopic=104157&page=2 Great minds think alike. Sad thing is I never looked at that post.

I've mauled mine pretty well with a pair of pliers, don't think its plated.

I'll be honest, I hated the look of the nordic. I know that is shallow, and a bit against my normal "Function over form" mentality. I'm sure it worked great, like all their products do. This is my first go around doing anything like this. Always been a wood worker in the past, so any suggestions on what alloy, or design changes ya'll would like to see, feel free to shout them out or email/pm me.

What alloy steel are you planning on making them out of? Not sure yet. Need to discus that with whoever will be making it. I'm a bit worried about the 4.5mm round section that attaches to the main body.

Thanks. Trying to get some quotes now. Also, the darker, main surface will be knurled. Couldn't figure out how to get the texture to display

Looks like my original set up will be cost prohibitive (minimum $50-75 each MY cost @ 50 units) New one I'm working on.

Limitation at the moment is not having a mill.

Im shooting for at, or below nordics pricing. Depends on how much clean up work I have to do to the weld to be honest. I was thinking of just doing a quick clean up, and dipping in a plastidip or something similar.

Any interest in a handle style like this? I know it wont work very well for you lefties out there.

I was trying to avoid that. I'm thinking about just bending appropriately sized round stock and notching it where needed. Sent from my HTC Droid Incredible 2 using Tapatalk 2

I have a design drawnup for one in solidworks...can't find a machinist to make me a test piece for under 300. Sent from my HTC Droid Incredible 2 using Tapatalk 2

I'm in the same boat. Bought mine on the 14th, still waiting for it to get shipped. Going to have a buddy fabricate me a bolt handle, if it works well I may have him do a run of them for me.

Happen to have a picture of it? I can't find any of the 26's in stock anywhere.

Was taking both in consideration. Limited I'm limited to 9 in the gun, and dont know how feasible I will be jamming a couple in after the buzzer.

Any reason yall can think of for getting the 28" ALS model for shooting limited? Or just stick with the utility?