himurax13
-
Posts
1,317 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by himurax13
-
-
-
22 hours ago, SISIG said:
Do a plunk test
I can't reiteratte this enough. Especially for the Tanfoglio and CZ-75 platforms.
-
6 hours ago, ddc said:
Those have actually been around for years.
Two headstamps that come to mind are FM and IMT.I think Ammoload also but it's been a while...
I've loaded them without issue for 9mm minor but I've heard PCC guys have a problem with separation at the step.
That would be aggravating to say the least.
I've got access to enough "normal" brass so I now throw these in the culls pile.
These have caused case head seperation in PCC's. I suspect they would do the same with 9mm Major.
-
They would fit just fine in Limited or limited 10 minor.
It would take more money than the retail value of these guns to make them into competitive open guns.
These guns should be compatible with many Tanfoglio parts. I suspect Tanfoglio double action parts could be made to work but that won't allow it to be used in Production or Carry Optics.
-
I use a circular tupperware bowl and I shake vigourously after spraying.
-
You could try Titegroup, N320, SW Clean Shot, or Win 231. They would feel similar compared to what you are using now.
-
1 hour ago, TonytheTiger said:
Turns out I wore out/rounded over the catch surface on my gen 1 TS (figured it out the painful way at a major too) and it's time for a replacement. Thing is, I've shaved the release button significantly and now I'm wondering if any of the myriad CZ75 mag releases will fit? They're closer to the size I want and cost half of what the TS part that needs butchering goes for.
Hoping @eerw knows something about this.
No.
-
-
Hopefully you can seat those Ginex primers deep. They seem to have light primer strike issues with them.
-
On 8/4/2022 at 12:33 PM, Furrly said:
3.8 - 4.0gr of N320 Should put you in the ball park, you might want to add what gun you are shooting these out of.
This is a great point. 3.8g of Titegroup/Clean Shot behind a 124g will get me 130ish PF out of most of my Production/Carry optic guns.
-
On 5/23/2022 at 4:43 AM, Arcrunner said:
I got a set of the RN 125 grain, before they were correctly renamed as 127 gr, and I also had to load quite short in my Shadow, the bullet profile is not friendly to short leade barrels like the Shadow, stock. Most recently I picked up the 150gr bullets and I noticed that the coating came off in small spots while they were in transit, not all of them, but enough that I noticed a green powder on my fingers after I loaded a hundred rounds. When I initially got the 125gr, they were the first of the new batch of color and they were losing their coating quite easily. confirmed to be a bad batch by BMB.
They shoot well, but to be honest, I don't like that the coating is still not exactly there. I may still stick to SNS as the coating is very sturdy on those.I use the 124g 9mm in my open gun at 172 PF...
-
The Ginex primers that I have used seem to cause light primer strikes in Sig P320, CZ75, and my DA/SA Tanfoglios.
-
Just now, himurax13 said:
I
I had J and L gunsmithing install Dawson Fiber Optic sights on some of my older slides.
-
-
I reccomend using a large white terry cloth towel when dissasembling the mag release. The pin can be easily lost.
-
On 8/24/2022 at 5:21 AM, bobbyblaze said:
Outstanding! I appreciate your response
I use the .40 caliber ones for my Large Frame Limited Tanfos.
-
3 hours ago, bobbyblaze said:
Will the MBX 140mm mags fit and work for IFG Large Frame TANFO STOCK 2 / for Carry Optics?
Yes. Just make sure it is the right caliber.
-
Is it possible to add a thigh pad to a DAA race master holster?
-
6 hours ago, thermobollocks said:
The way Taccom does their feed ramps can interfere with the last round bolt hold open setups. Their press-fit ramp is like that, and I don't know if their fully ramped barrels have that issue with every manufacturer. Angstadt it's not an issue, but it's also one more part that can fail. I left mine out since I'm basically never shooting to bolt lock. In my case, I'd only ever want it for some of those insane high round count 3-gun stages, and even that is just because I don't practice reloading into a 40-rounder.
It does interfere with the FM9 lower but works just fine with the Aero lower. LRBHO and short stroke work perfectly with an Aero Upper and lower with the Taccom ESSB and superfeed barrels.
-
I was looking at 3 different kynshot buffers and I was trying to figure out the best way to test what is best for double tapping with a 10" barrel and 6" brake (100g & 115g) and a 5.5" barrel and brake (124g & 147). Sumply watching the dot bounce is difficult to judge.
1. 5015, Orange Spring, and buffer tube spacer.
2. 5020, Red Spring, buffer tube spacer, A5 tube.
3. 5006, JP Polished Carbine Spring, buffer tube A5 Tube.
-
You will need to go to an online vendor such a Cajun Gunworks, CZ Customs, Patriot Defense, or Wolff Springs to get a larger variety. The ammo you use will determine what spring you will need.
-
I found this data online, however I would probably start at 4.2g
-
Has anyone used the .380 95 grain double struck heavy plated bullets for PCC? Were you able to make PF? What OAL did you use.
Thanks in advance.
-
Should be similar to Tg. I would start at 4.3g. A lot depends on the barrel.
How many coils?
in CZ
Posted
If you count the top and bottom coils, I see 13 on the left and 11 on the right.